Door - Bottom Weatherstrip
p/n: 70-0744-73
Door Bottom Weatherstrip - The door bottom weatherstrip for front and rear doors. A four (4) piece set for all 4 doors. Molded to exact as original profile.
Front or Rear Door Weatherstrips
p/n: 90-0128-72
This Front or Rear Door Weatherstrip set is the primary weatherstrips for the door to the body. The set contains two (2) weatherstrips for either the front or the rear doors. Purchase two (2) sets if you need to complete all four (4) doors.
Rear Window Division Bar Seal
p/n: 70-1845-82
Weatherstrip, back window divider. Four (4) piece set.Length: 13.0 inches.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Hood to Cowl Side Extension Filler
p/n: 70-2258-43
This Hood to Cowl Side Extension Filler pair is fully molded from soft EPDM sponge rubber with all original details.
License Light Mounting Pad
p/n: 70-1221-17
Pad set, license light mount and lens gasket.Length: 12.625 inches.
Rear Door Hinge Pillar Filler
p/n: 70-2226-79
This Rear Door Hinge Pillar Filler seal pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window, and may also be known as a door u-jamb seal. Fully molded authentic rubber construction with brass metal core.
Wheel cover cushion
p/n: 70-0094-38
Cushion strip for large hubcap (wheel cover). Original type, replaces that old brittle rubber to keep from losing the cover. Set of four (4) strips, approximately four (4) foot long, enough for all four (4) wheels.
Front Door Weatherstrips
p/n: 70-0824-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (pin-on) directly to the left and right front doors sealing the doors against the vehicle body when the door is closed.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2494-45
This ten (10) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Trunk Weatherstrip
p/n: 70-0796-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Coil spring insulator pad
p/n: 70-0801-32
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Engine Mount Pad
p/n: 70-0740-11
This Engine Mount Pad pair is designed from the original for an exact original configuration. Two (2) per car.
Rear Window Division Bar Seal
p/n: 70-0475-82
Pad/Gasket set, back window division bar mounting. Set of four (4) pads, inner and outer, for two (2) dividers. Three fourths (3/4) inch wide.
Front or Rear Door Seals
p/n: 90-0130-72
Door edge weatherstrip. Two door seals. Used for the front doors on Chevrolet, Oldsmobile & Pontiac models. Also used for the front or rear doors on Buick models. If needing all four (4) door seals for Buick purchase two (2) pairs. This part is the primar
Front Suspension Rebound Pad
p/n: 50-0083-32
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Rear window division bar seal
p/n: 70-0414-82
Pad set, back window division bar. Molded with screw clearances. Four (4) piece set.
Taillight Gasket
p/n: 70-0706-15
Gasket set, rear and back up light installation. Sold in ten (10) piece set only. (A) Gasket, rear light body. twenty two (22) inches overall.
Door weatherstrip
p/n: 70-0504-73
Weatherstrip, door bottom on door, rubber only, retained by steel strip. Four (4) piece set.
Firewall Grommet Set
p/n: 70-1148-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Axle Rebound Pad Service
p/n: 70-0502-32
Bumper, rear spring to frame, two (2) per car.Width: 2.5 inches. Height: 2.5 inches.
License Light Mounting Pad
p/n: 70-1222-17
Pad set, license light mount and lens gasket.Length: 12.625 inches.
Window Sash Steel Channels
p/n: 70-0846-58
This Window Sash Steel Channel pair is designed from the original part for superior fitment and function. Ready for attaching to your original brackets. Thirty-two and three eighths (32-3/8") inches long.
Front Bumper Grommet
p/n: 70-0041-28
Grommets, front bumper. Hollow construction, fully duplicates original.
Front or Rear Door Weatherstrips
p/n: 82-0150-72
This is a universal push-on type Door Weatherstrip. Made with flexible steel core. Can be used for the front or rear passenger entry doors.
Side Mount Spare Grommet Set
p/n: 70-1134-37
This Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Door Edge Weatherstrips
p/n: 60-0247-72
This Door Edge Weatherstrip pair is designed from the original parts for superior fitment and seal to keep the elements out and reduce road noise while driving. These door edge weatherstrips mount, with pre-installed pins, to seal the Left and Right doors when closed.
Rear Quarter Window Filler
p/n: 70-3505-67
This Rear Quarter Window Filler pair is designed from the original part for superior fitment and seal. This is the rear quarter window folding top cover retainer guide with strip. Fully molded with a brass metal core and includes hardware.
Axle Rebound Pad
p/n: 70-0238-32
Pads, axle rebound, rear two and one fourth (2-1/4) inches diameter by three (3) inches high.Height: 3.0 inches.
Front Door Weatherstrips
p/n: 70-2216-72
This Front Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Push-on type door seals mount directly to the body to seal against the full perimeter of the front doors.
Rear Door Weatherstrips
p/n: 70-2218-72
This Rear Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Push-on type door seals mount directly to the body to seal against the full perimeter of the rear doors.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
Parking light gasket
p/n: 70-0190-16
Gasket set, parking light and front turn signal. Four (4) piece set.
Brown Accelerator Service
p/n: 25-0050-89
Pad, accelerator pedal. Exact copy in brown rubber. Revulcanization service only. Color: brown Length: 9.0 inches.
Brake Vacuum Cylinder Rod Boot
p/n: 30-0115-24
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material. Length: 6.0 inches.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Engine Mount Pad
p/n: 70-1162-11
This Front Engine Mount Pad pair is designed for cars with round cone type front engines. For V-12 and V-16 models.
Firewall Grommet Set
p/n: 70-1149-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Roof Rail Filler
p/n: 70-0396-67
Fillers, side roof rail to front roof rail at front corner, right and left. Metal core, threaded for original screws.
Taillight Mounting Pad
p/n: 70-0216-15
Pads, taillight bracket to fender mounting.Length: 5.75 inches.
U Jamb Lock Pillar Fillers
p/n: 70-1617-79
This Quarter Window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
License Light Mounting Pad
p/n: 70-1220-17
Pad set, license light mount and lens gasket. Length: 12.0625 inches.
Shock and Stabilizer Seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set. Width: 1.1875 inches.
Side Deflector / Valance Rubber
p/n: 70-0092-45
This Side Deflector / Valance Rubber pair is designed from the original part for superior fitment and seal. Each deflector piece is approximately 6 feet long.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2493-45
This six (6) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Trunk Weatherstrip
p/n: 70-0988-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Side Mount Spare Grommet Set
p/n: 70-1137-37
This Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Windshield Division Bar Gasket
p/n: 70-0486-51
Weatherstrip. windshield divider post, outer, brass core. Acts as retainer for outer chrome. Similar to our #70-0159-51 but shorter, twelve (12) inch overall.
Engine Mount Pad
p/n: 70-1161-11
This Engine Mount Pad pair is designed from the original for an exact original configuration. For cars with round cone-type front mounts.
Front Bumper Grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Hood Ventilator Bumper Set
p/n: 70-0011-42
This forty (40) piece Hood Ventilator Bumper set is designed from the original parts for superior fitment and function. The set includes bumpers and rivets for one (1) hood.
Rear Bumper Grommet
p/n: 70-0144-29
Grommets, rear bumper (Some cars have this type, some have our #70-0164-29, sold separately. They are both interchangeable and original). Fully molded rubber.
Side Mount Spare Grommet Set
p/n: 70-1136-37
This six (6) piece Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Engine Yaw Control Arm Service – Revulcanization Only
p/n: 70-0778-11
This Revulcanization Service Only is designed to restore your Engine Yaw Control to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Firewall Grommet Set
p/n: 70-1147-21
This Firewall Grommet Set contains six (6) pieces intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Hood ventilator wedge pad
p/n: 70-0317-42
Wedge pads, hood side ventilators. Fourteen (14) piece set.
License Light Mounting Pad
p/n: 70-1223-17
Pad set, license light mount and lens gasket.Length: 12.625 inches.
Taillight Gasket Kit
p/n: 70-0972-15
Gasket set, taillight and backup light assembly to fender. Four (4) piece set.
U Jamb Lock Pillar Fillers
p/n: 70-1912-79
This U Jamb Lock Pillar Filler serves to seal the bottom of the rear side window and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core.
Front Suspension Bumper
p/n: 70-1022-32
Bumper, front suspension, lower on spring seat. Made with long lasting Buna rubber.1958: Also used on other models with air suspension.Width: 1.875 inches.
Lower Suspension Arm Dust Seal Set
p/n: 70-0865-32
This four (4) piece Lower Suspension Arm Dust Seal Set is fully molded of high-quality EPDM dense rubber for durability and proper fitment. These seals are used to protect your lower suspension arm bushings from dust and debris.
Engine Mount Service – Revulcanization Only
p/n: 70-0669-11
This Revulcanization Service Only is designed to restore your Upper Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
