Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Outer Beltline Weatherstrip
p/n: 70-0879-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outline Beltline Weatherstrip
p/n: 70-0860-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Parking and Fog Light Lens Gaskets
p/n: 70-3159-16
This Parking and Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking and Fog Light Lens and the Parking and Fog Light Housing or Bezel.
Parking/Backup Light Lens Gaskets
p/n: 70-1272-16
This Parking/Backup Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Housing or Bezel. Die-cut from one-eighth (1/8") inch sponge rubber.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Phototube Mounting Pad
p/n: 70-0721-17
Pad, phototube mounting on instrument panel. Automatic headlight beam control.Length: 2.3125 inches. Width: 1.6785 inches.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Quarter Window Bumper
p/n: 70-1583-62
Bumper, quarter window stop on sash channel.Length: .8125 inches. Width: .75 inches. Height: .50 inches.
Quarter Window Lock Pillar Fillers
p/n: 60-0602-79
This Quarter Window Lock Pillar Filler pair seals the bottom of the rear side window, and may also be known as a u-jamb or door jamb seal. Fully molded authentic rubber construction with brass metal core.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Radiator Air Deflector
p/n: 70-3478-31
This Radiator Air Deflector is designed from the original part for superior fitment and seal. Part is die cut from quality masticated rubber to authentic original dimensions. Deflector attaches to the front lower portion of the radiator support.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Radiator Side Fillers
p/n: 70-4925-31
These two (2) piece Radiator Side Fillers are designed from the original part for superior fitment and function. Filler pieces are die cut from quality 3/32" masticated rubber to authentic original dimensions.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.