Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Windshield Division Bar Gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Trunk Hinge Mounting Pads
p/n: 70-1230-87
This four (4) piece Trunk Hinge Mounting Pad is designed from the original part for superior fitment and function. The installed length is 5-1/2" inches.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Windshield Wiper Transmission Gaskets
p/n: 70-1196-53
This Windshield Wiper Transmission Gasket pair is designed from the original part for superior fitment and function. This gasket mounts between the windshield wiper transmission and the vehicle body work to reduce noise and vibration.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Stabilizer Grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Shock Absorber Bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
2-1/4" Firewall Grommet
p/n: 32-0225-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Door handle ferrule grommet
p/n: 70-0173-69
Grommet for outside door handle ferrule. Similar to, but not interchangeable with our #70-0009-69.
Body Mounting Pad
p/n: 70-0264-48
This Body To Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs under body mount / washer below bracket. Fully molded high quality EPDM rubber.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
1-5/8" Firewall Grommet
p/n: 32-0226-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the handbrake cable.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Door Handle Grommet
p/n: 70-0009-69
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
Stabilizer and Shock Washer
p/n: 70-0395-33
Washer, tapered, rear stabilizer and shock arm ball joint retainer. Fully molded rubber.
1-9/16" Firewall Grommet
p/n: 32-1201-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Typically used for wiring.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
9/16" Door Edge Weatherstrip
p/n: 70-0411-73
This Door Edge Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brake Cable Shielding Cover - 2 Inch
p/n: 70-1701-24
This two (2) inch long Brake Cable Shielding Cover is designed install for an authentic fit, finish and function. Fits all models with seven sixteenths (7/16) inch outside diameter cable.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
1/2" Door Bottom Weatherstrip
p/n: 70-0066-73
This Door Weatherstrip is designed for the bottom of the door and is held in by a metal track or by clips. Available by the foot.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
3/4" Roof Rail Weatherstrip
p/n: 70-1170-99
This available by the foot Roof Rail Weatherstrip measures three fourths inches (3/4") in height. It fits into a metal channel retainer. Note: Order twelve feet (12') for two (2) door models and fourteen feet (14') for four (4) door models.
7/8" Window Weatherstrip
p/n: 70-1188-52
This Window Weatherstrip is for models with heavy weatherlip and notch for bead reveal molding. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1191-52
This Window Weatherstrip is for models without chrome reveal molding. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1192-52
This Window Weatherstrip is for models with chrome reveal molding. Available by the foot.
7/8" Windshield Weatherstrip
p/n: 70-1190-52
This Windshield Weatherstrip is for windows without chrome reveal molding. For a 2-piece windshield, select gasket for division bar. Available by the foot.
9/16" Channel filler weatherstrip
p/n: 70-0489-58
Weatherstrip, channel filler, door window sash channel and some quarter window sash channel. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary. Available by the foot.
Wheel Cover Cushion
p/n: 70-0633-38
Filler, wheel cover to wheel. Approximately two and one eighth (2-1/8) inches long each, twenty (20) required per car. (Five (5) per wheel cover).
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
11/16" Wiring Grommet
p/n: 32-0161-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment. This grommet is made from quality dense rubber to provide excellent durability. Designed for the spark plug wire organizer bracket.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/16" Filler and Cushion Strip
p/n: 70-1236-48
Filler and cushion strip with a variety of applications. Available by the foot.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
3/4" Trunk Weatherstrip
p/n: 70-0518-85
This Trunk Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Also has many additional uses outside of its original purpose. Available by the foot.
1/2" Door Top Seal
p/n: 70-0065-73
This Door Top Seal is made of high-quality EPDM dense rubber. The weatherstrip is an excellent copy of the original and fits into a light metal track. Available by the foot.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Front Bow Weatherstrip Retainer Clip
p/n: 70-0527-67
This Front Bow Weatherstrip Retainer Clip is designed from the original part for superior fitment and function. This fastener is most commonly used to retain #70-0138-64 and #70-0157-64 front bow weatherstrips. A Cadmium plated retainer requiring a one-quarter (1/4) inch opening.
3/4" Side Window Weatherstrip
p/n: 70-0064-57
Seal, lower side window. Fastens to inner face of door to seal against outer side of glass. Available by the foot.
3/8" Side Window Weatherstrip
p/n: 70-0079-58
Weatherstrip, side window lower edge. Available by the foot.
1/2" Standard Bumper
p/n: 33-0136-42
This Standard Bumper is fully molded from quality dense rubber to provide excellent durability. Commonly used as a door bumper on the center upper post on post model vehicles.
Door Weatherstrip Fastener Clip
p/n: 70-0303-73
Metal Fastener clips, sold as an each, for attaching door edge weatherstrips. For one fourth (1/4) inch holes. Doors usually require one (1) clip per every six (6) inches.
Door Weatherstrip Fastener Retaining Clip
p/n: 70-0391-73
This Door Weatherstrip Retaining Clip is manufactured to OEM specifications to install for an authentic fit, finish and function. A direct-fit for Lower Door Weatherstrip 70-0066-73. Fits one-fourth (1/4") inch holes. Usually requires one clip per every six (6") inches.