Door Bumper
p/n: 33-0503-71
This fully molded 3/4” Door Bumper is quality reproduction of the original factory part. Not a generic substitute but manufactured just like the factory original.
Door Bumper
p/n: 33-1233-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 34-0469-71
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Door Bumper
p/n: 33-1232-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 33-1234-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Center Post Weatherstrips
p/n: 70-0847-73
This four (4) piece Door Center Post Weatherstrip set is designed from the original part for superior fitment and seal. A four (4) piece set for the left and right, front and rear doors. Authentic cross-section and construction.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Door Conduit
p/n: 70-0828-21
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Door Drain Hole Seal
p/n: 60-0442-70
This Door Drain Hole Seal installs on the door bottom and is also used on the tailgate of station wagons. Two (2) required per vehicle. Molded from high-quality EPDM dense rubber.