Front or Rear Door Weatherstrips
p/n: 82-0150-72
This is a universal push-on type Door Weatherstrip. Made with flexible steel core. Can be used for the front or rear passenger entry doors.
Front Bumper Grommet
p/n: 70-0041-28
Grommets, front bumper. Hollow construction, fully duplicates original.
Window Sash Steel Channels
p/n: 70-0846-58
This Window Sash Steel Channel pair is designed from the original part for superior fitment and function. Ready for attaching to your original brackets. Thirty-two and three eighths (32-3/8") inches long.
Axle Rebound Pad Service
p/n: 70-0502-32
Bumper, rear spring to frame, two (2) per car.Width: 2.5 inches. Height: 2.5 inches.
License Light Mounting Pad
p/n: 70-1222-17
Pad set, license light mount and lens gasket.Length: 12.625 inches.
Door weatherstrip
p/n: 70-0504-73
Weatherstrip, door bottom on door, rubber only, retained by steel strip. Four (4) piece set.
Firewall Grommet Set
p/n: 70-1148-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Rear window division bar seal
p/n: 70-0414-82
Pad set, back window division bar. Molded with screw clearances. Four (4) piece set.
Taillight Gasket
p/n: 70-0706-15
Gasket set, rear and back up light installation. Sold in ten (10) piece set only. (A) Gasket, rear light body. twenty two (22) inches overall.
Front or Rear Door Seals
p/n: 90-0130-72
Door edge weatherstrip. Two door seals. Used for the front doors on Chevrolet, Oldsmobile & Pontiac models. Also used for the front or rear doors on Buick models. If needing all four (4) door seals for Buick purchase two (2) pairs. This part is the primar
Front Suspension Rebound Pad
p/n: 50-0083-32
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Engine Mount Pad
p/n: 70-0740-11
This Engine Mount Pad pair is designed from the original for an exact original configuration. Two (2) per car.
Coil spring insulator pad
p/n: 70-0801-32
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Rear Window Division Bar Seal
p/n: 70-0475-82
Pad/Gasket set, back window division bar mounting. Set of four (4) pads, inner and outer, for two (2) dividers. Three fourths (3/4) inch wide.
Trunk Weatherstrip
p/n: 70-0796-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2494-45
This ten (10) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Front Door Weatherstrips
p/n: 70-0824-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (pin-on) directly to the left and right front doors sealing the doors against the vehicle body when the door is closed.
License Light Mounting Pad
p/n: 70-1221-17
Pad set, license light mount and lens gasket.Length: 12.625 inches.
Wheel cover cushion
p/n: 70-0094-38
Cushion strip for large hubcap (wheel cover). Original type, replaces that old brittle rubber to keep from losing the cover. Set of four (4) strips, approximately four (4) foot long, enough for all four (4) wheels.
Hood to Cowl Side Extension Filler
p/n: 70-2258-43
This Hood to Cowl Side Extension Filler pair is fully molded from soft EPDM sponge rubber with all original details.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Rear Door Hinge Pillar Filler
p/n: 70-2226-79
This Rear Door Hinge Pillar Filler seal pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window, and may also be known as a door u-jamb seal. Fully molded authentic rubber construction with brass metal core.
Rear Window Division Bar Seal
p/n: 70-1845-82
Weatherstrip, back window divider. Four (4) piece set.Length: 13.0 inches.