Outer Beltline Weatherstrip
p/n: 70-0803-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Vent division bar weatherstrip
p/n: 70-0783-74
Division bar seal. Made with metal core and attaching tabs like original. Rear door on models with rear door vent.
Taillight to Body Weatherstrips
p/n: 70-0701-15
This Taillight To Body Weatherstrip pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body. Twenty-three and three fourths (23-3/4) inches developed length.
Air Conditioning Pipe Grommet
p/n: 70-0934-31
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Hood Corner Pad
p/n: 70-0914-42
Pad, hood corner. Molded left and right like original.Width: 1.375 inches.
Fuel Neck Grommet
p/n: 70-0404-39
Grommet, fuel filler neck. Fully molded rubber. Flat bottom has slight ridge (seam) along edge. Four and three eighths inch (4-3/8") outside diameter by two and three sixteenths inch (2-3/16") inside hole diameter by five eighths inch (5/8") height.
Rear Bumper To Body Filler
p/n: 70-3079-30
This Rear Bumper To Body Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. This piece fits between the rear bumper and the vehicle body.
Side Window Vertical Leading Edge
p/n: 70-1271-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Cowl Vent Gasket
p/n: 70-0194-54
Gasket, cowl vent. Original solid rubber configuration, not a sponge substitute.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Rear Door Pillar Filler
p/n: 70-0837-79
This Rear Door Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a door jamb seal.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.