Side Window Weatherstrip Set
p/n: 90-3288-90
This six (6) piece Side Window Weatherstrip Set is designed for superior fitment and function. The set contains the flexible run channels and the window felt beltline weatherstrips needed for the side window glass. The set does two (2) front doors.
Transmission Mount Service
p/n: 60-0647-24
Mount, transmission support. Revulcanization service only.
Windshield Gasket
p/n: 60-0169-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Windshield Gasket
p/n: 60-0083-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Flexible Run Channel
p/n: 60-0129-58
Flexible corrugated steel, cloth covered and mohair lined. Available in 90" lengths.
Windshield Gasket
p/n: 70-1945-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Front Spring Bumpers
p/n: 60-0393-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. These axle to frame bottoming rebound pads are dense rubber blocks that mount to the front axle.
Side Window Beltline Scraper Weatherstrips
p/n: 60-0566-58
These inner and outer Side Window Beltline Scraper Weatherstrips slide into the groove on top of the door's window opening and wipes the glass when window is raised and lowered. Four (4) piece set.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Cowl Vent Gasket
p/n: 60-0124-54
Gasket, cowl vent. Original labyrinth style, not sponge.Length: 16.5 inches. Width: 4.0 inches.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
Gearshift Gasket
p/n: 60-0397-24
This sponge rubber Gearshift Gasket is one-half (1/2) inch thick. For the gearshift at floorboard. One required per vehicle.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Beltline Rubber Scraper Weatherstrip
p/n: 60-0287-58
This Beltline Rubber Scraper Weatherstrip pair is designed from the original part for an authentic fit, finish, and appearance. Fits at the door outer window at beltline. Each strip approximately is twenty-six (26) inches to twenty-seven (27) inches long.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Clutch and Brake Pedal Pads
p/n: 60-0218-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Bumpers
p/n: 60-0579-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. This pedal to floorboard bumper is the longer type with one and three-eighths (1-3/8") inch clearance for the pedal shaft.
Door Weatherstrips - Lower
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Cowl Vent Drain Hose
p/n: 60-0381-54
This Cowl Vent Drain Hose is designed from the original part for superior fitment and seal. Length: 7-1/4" inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
1-11/16" Firewall Grommet
p/n: 60-0057-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from original parts for excellent workmanship.
Ferrule and Grommet Set
p/n: 70-0597-69
This Ferrule and Grommet Set for the outside door handle is cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Steering Column Gasket
p/n: 60-0435-32
This Steering Column Gasket is designed from the original part for superior fitment and sealing. Gasket is die cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Hood Side Upper Bumper
p/n: 70-2617-42
This Hood Side Upper Bumper is fully molded with top quality EPDM rubber. The authentic configuration for 1/4" hole. Six (6) bumpers typically required per vehicle.
Rear Spring Shackle Rubber Bushing
p/n: 60-0236-48
This Rear Spring Shackle Rubber Bushing is designed from the original part for an authentic fit, finish and function. Bushing fits left or right-hand side and upper or lower spring eye.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.