Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Hood Bumper Set
p/n: 33-0681-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Body to Frame Mounting Pad
p/n: 60-0188-48
This Body to Frame Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with a metal core, locating collar, and metal bolt. Two (2) required per vehicle.
Front Fender Seal
p/n: 60-0438-45
Seal, vertical, front quarter panel (fender) to cab at rear of fender (cowl). Two (2) piece set for both sides of cab.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Fuel Neck Grommet
p/n: 60-0475-41
Grommet, fuel filler neck (1955-2nd type). Fully molded rubber, slightly oblong. Three and one half inch (3-1/2") outside width by three and fifteen sixteenths inch (3-15/16") outside length.
Wiring Harness Grommet
p/n: 70-2113-20
This Wiring Harness Grommet is designed from the original part for superior fitment and seal. The grommet installs for an authentic fit, finish and function. Fully molded with proper lips and pass through holes for main harness electrical wiring.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Accelerator Pedal Pad
p/n: 60-0301-41
Pad, accelerator pedal. Slipover cover type. Exact copy. Fits original steel core. Length: 8.0 inches.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Vent Window Division Post Weatherstrips
p/n: 60-0585-56
This Front Door Vent Window Division Posts Weatherstrip pair is fully molded with a metal core and attachment holes. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Engine Mount
p/n: 25-0060-11
This Engine Mount is for the lower front. Lower Front. Designed to original specifications for an authentic fit and appearance. The mount supports the engine and dampen vibration.
Headliner Retainer Strip
p/n: 60-0368-88
Retainer strip. Holds cardboard headliner in place. Twelve (12) foot strip.Length: 144.0 inches. Width: .5625 inches.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Flexible Run Channel
p/n: 60-0375-58
For windows with metal glass frames. Flexible corrugated steel, cloth covered, mohair lined. Available in 5ft lengths.
Axle Bumpers
p/n: 60-0491-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming rebound pads are dense rubber blocks that mount to the rear axle tube.
Body Bumper Kit
p/n: 90-0213-90
This sixteen (16) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Window Felt Beltline Weatherstrips
p/n: 80-0056-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This four (4) piece set includes inner and outer window felt beltline weatherstrips for each door side window.
Rear Window Gasket Set
p/n: 60-0182-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a thirteen foot, one inch (13' 1") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Front Door Weatherstrips
p/n: 60-0485-72
This Front Door Edge Weatherstrip pair is the primary door to body weatherstrip. This smaller for 1955-2nd type weatherstrip pair is the proper length door edge seal which attaches to the door with pre-inserted plastic attaching pins.
Windshield Gasket with Groove
p/n: 60-0379-50
This Windshield Gasket with Groove mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the groove slot to accommodate the outer edge's decorative reveal molding.
Windshield Gasket without Groove
p/n: 60-0289-50
This Windshield Gasket without Groove is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. For models with no reveal molding.
Front Door Vent Window Weatherstrip Set
p/n: 60-0297-55
This four (4) piece Door Vent Window Weatherstrip Set contains the main vent window and division post weatherstrips. All of the pieces were designed from original parts for a precise, factory fit. The division post weatherstrips contain a brass core for durability and easy installation.
Window Felt Beltline Weatherstrips - Vent Window Delete
p/n: 80-1106-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This four (4) piece set is custom made for vehicles with the vent or wing windows removed.