Taillight Mounting Pad
p/n: 60-0116-15
Pad, taillight bracket to fender. Four (4) inches long. Compare with our #60-0172-15 and #60-0545-15. Length: 4.0 inches.
Lower Door Weatherstrips
p/n: 60-0047-73
This Lower Door Weatherstrip pair is designed from the original part for superior fitment and seal. Each 36" length weatherstrip fastens to the cab threshold.
Steering column seal
p/n: 60-0478-36
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Splash Apron / A-Arm Dust Shield
p/n: 70-3058-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Clutch or Brake Pedal Pad
p/n: 60-0467-22
This reproduction Clutch or Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Splash Apron / A-Arm Dust Shield
p/n: 70-3216-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Hood to Cowl Weatherstrip
p/n: 70-3924-43
This Hood to Cowl Weatherstrip has the proper rubber cross section and is made from top quality rubber to ensure durability and seal. Designed from the original part for a superior fitment and seal.
Steering Column Spacer
p/n: 60-0563-32
Spacer, steering column to dash at U-clamp.Length: 2.50 inches.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Door Jamb Wire Loom Grommets
p/n: 70-4870-70
These Door Jamb Wire Loom Grommets go between the door and door jam and allow you to run wires or cables through them. They make great complements to power window kits, shaved door kits, or custom stereo installs.
Body to Frame Mounting Pad
p/n: 60-0188-48
This Body to Frame Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with a metal core, locating collar, and metal bolt. Two (2) required per vehicle.
Lower Door Weatherstrips
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Windshield Division Bar Gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Firewall to Fender Dust Shield Seals
p/n: 70-3491-45
This two (2) piece Firewall To Fender Dust Shield seal pair is designed from the original part for superior fitment and seal. Fender seals attach to firewall sides to seal the space between the firewall and the inside of the front fenders.
Hood To Cowl Weatherstrip
p/n: 70-4693-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Trunk Handle Grommet
p/n: 50-0183-87
Grommet, trunk handle bezel-thru-trunk lid. Special size, one (1) inch inside diameter.Buick 1937 Grommet, trunk handle bezel-thru-trunk lid.
Accelerator Rod Button Cover
p/n: 60-0357-40
Cover, accelerator rod button. Round slip-over type. Good copy with bow tie center. Height: .4375 inches.
Taillight Gasket
p/n: 60-0692-15
Seal, taillight bezel. Correct profile and long lasting material. Two (2) strips cut twenty four and three fourths (24-3/4) inches long.Length: 24.
Taillight Gasket
p/n: 60-0694-15
Seal, taillight bezel. Correct profile and long lasting material. Two (2) strips cut fourteen and three fourths (14-3/4) inches long.
Headlight Outer Rim Seal
p/n: 27-0063-14
Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-2799-45
This Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pair pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Rear Cargo Door Upper Weatherstrip
p/n: 70-4703-73
This Rear Cargo Door Upper Weatherstrip is designed from the original part for superior fitment and seal. Push-on type door weatherstrip mounts on the upper portion of the body and seals against the closed cargo doors.
Splash Apron / A-Arm Dust Shield Fillers
p/n: 70-3483-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Taillight Mounting Pad
p/n: 60-0472-15
Pad, taillight bracket mounting. Two and three sixteenths (2-3/16) inch by three and three fourths (3-3/4) inch inside of bead.
Clutch and Brake Pedal Bumpers
p/n: 60-0579-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. This pedal to floorboard bumper is the longer type with one and three-eighths (1-3/8") inch clearance for the pedal shaft.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Hood to Cowl Weatherstrip
p/n: 70-4800-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Taillight Mounting Pad
p/n: 60-0364-15
Pad, taillight mounting to rear fender. Length: 1.0625 inches.
Roof Rail Fillers
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Clutch and Brake Pedal Pads
p/n: 60-0218-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Taillight Mounting Pad
p/n: 60-0495-15
Pad, taillight bracket to fender. Can be used for right or left hand. Two and one half (2-1/2) inch by three and five eighths (3-5/8) inch overall.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
This Steering Column Connecting Rod Seal is designed from the original part for superior fitment and function. Fully molded with top quality EPDM rubber to ensure long durability.
Stabilizer Shaft Link Bushing
p/n: 60-0317-33
This Stabilizer Shaft Link Bushing works to support the vehicle front stabilizer or sway bar shaft. Six (6) required per vehicle.
Convertible Top Rail Cushions
p/n: 70-3438-67
Convertible top cushion pads. These parts go between the first & second section of the roof rail for both the left and right sides.
Fuel Filler Neck Inner Panel Grommet
p/n: 70-1908-41
This Fuel Filler Neck Inner Panel Grommet is designed from the original part for superior fitment and seal. This flat grommet fits around the vehicles fuel filler neck at the inner panel.
Trunk Weatherstrip
p/n: 70-0774-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Hood To Cowl Weatherstrip
p/n: 82-0215-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Cowl Vent Gasket
p/n: 60-0044-54
Gasket, cowl vent. One (1) piece sponge rubber shear die cut to correct dimensions. Replaces #4034247-8.
Front Fender Vertical Filler
p/n: 60-0438-45
This Front Fender Vertical Filler pair is designed from the original part for an authentic fit and function. The vertical fill piece between the front fender to cab at rear of fender (cowl). Two (2) piece set for both sides of cab.
Inner Fender to Cowl Filler Set
p/n: 70-3356-45
This six (6) piece Inner Fender to Cowl Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit at rear of fender to cowl panel.
Window Gasket Locking Strip - Chrome
p/n: 70-1919-52
This chrome appearing Window Gasket Locking Strip is designed from the original part for superior fitment and seal. Locking strip serves as the front or rear window gasket retainer. Sixteen (16') foot length single piece, one application, for complete coverage.
Trunk Weatherstrip
p/n: 70-0798-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Splash Apron Filler Shield Set
p/n: 70-2510-45
This four (4) piece Splash Apron / A-Arm Dust Shield Filler Set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Hood to Cowl Weatherstrip
p/n: 70-1446-43
Weatherstrip, hood to cowl seal. Approximately fifty seven (57) inches of extruded rubber.
License Light Mounting Pad and Grommet Set
p/n: 60-0337-17
This License Light Mounting Pad and Grommet Set is designed from the original part for superior fitment and function. Mounting Pad for the license light to trunk lid. The Grommet is for the license bracket spacer post.
Firewall Grommet
p/n: 60-0565-20
This Firewall Grommet is used to run the top hydraulic lines, wiring harness, and speedometer cable through the firewall. Designed from the original part for superior fit, finish and appearance.
Rear Door Bumpers
p/n: 60-0334-71
A Rear Door Bumper pair for the door check link above door. Dovetail base fits check arm.
Cowl Vent Gasket
p/n: 60-0131-54
Gasket, cowl vent. One fourth (1/4) inch by five sixteenths (5/16) inch, for five (5) inch by fifteen (15) inch top cowl vent. Sponge type.Width: 15.
Hood to Cowl Rear Weatherstrip
p/n: 70-4692-43
This Hood To Cowl Rear Weatherstrip is designed from the original part for superior fitment and seal. A reproduction manufactured to the original profile and design specifications. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Cowl Vent Gasket
p/n: 60-0087-54
Gasket, cowl vent, lip type. Sponge rubber, for three and seven eighths (3-7/8) inch by fifteen (15) inch cowl vent.Length: 15.0 inches. Width: 3.
Hood to Cowl Weatherstrip
p/n: 70-3448-42
This Hood to Cowl weatherstrip is for superior fitment and sealing. This extruded sponge rubber clinch seal strip mounts at the rear of the engine bay directly to the body on the cowl lip.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Side Window Glass Run Channels
p/n: 70-5022-58
These Side Window Glass Run Channels fit two (2) and four (4) door sedans and wagons. Channels come in a pair for both sides of the vehicle. Produced using premium quality, ozone resistant materials.
Taillight Lens Gasket
p/n: 60-0175-15
Gasket, taillight lens.Length: 3.50 inches. Width: 2.25 inches.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Exhaust System Hanger
p/n: 60-0307-13
This Exhaust System Hanger is used for the muffler-to-tailpipe support (insulator) with reinforced webbing. Fully molded from top-quality EPDM dense rubber to ensure durability. One (1) required per car.
Choke Cable Support At Ignition Cable Grommet
p/n: 60-0373-13
This Choke Cable Support At Ignition Cable Grommet is designed from the original part for superior fitment and function.
Fuel Filler Neck Grommet
p/n: 60-0474-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Floor Shift | Carpet Grommet
p/n: 70-3265-88
This Floor Shift / Carpet Grommet is designed from the original part for superior fitment and seal. This part seals the carpet edge to the floor shift boot. For models without floor console.
Fuel Filler Neck Grommet
p/n: 60-0149-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Oblong fully molded rubber with retaining flange.
Horn projector grommet
p/n: 60-0161-21
Grommet, horn trumpet through horn mounting bracket. For Deluxe country horn.
Taillight Mounting Pad
p/n: 60-0545-15
Pad, bracket mounting to body for tail and license plate light. Length: 3.3125 inches. Width: 2.5625 inches.
Upper Door Drip Rail Weatherstrip
p/n: 70-4880-73
This Upper Door Drip Rail Weatherstrip is made from high-quality ozone-resistant PVC rubber. This Left or Right single piece weatherstrip is installed onto the A-pillar, spanning along the upper section of the cab opening and extending down the rear side door of the 4-door trucks.
Taillight Gasket
p/n: 60-0691-15
This Taillight Gasket is made of fully molded soft-dense rubber compound to ensure proper installation and performance. Designed from the original part for the correct profile. Two (2) strips cut thirty-six (36) inches long.
Fuel Filler Neck Grommet
p/n: 60-0434-41
This Fuel Filler Neck Grommet is the inner grommet through the quarter panel inside fuel filler door. Fully molded rubber with retaining flange as original for good seal. Three and one eighth inch (3-1/8") outside diameter by two and one eighth inch (2-1/8") inside diameter.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Taillight Gasket
p/n: 60-0693-15
Seal, taillight bezel. Correct profile and long lasting material. Six (6) strips cut twelve and three fourths (12-3/4) inches long.Length: 12.75 inches.