Hood to Radiator Weatherstrip
p/n: 60-0011-42
This Hood to Radiator Weatherstrip is molded with four (4) carrot retainers, just as the original. The pair is nine (9) inches in length. Two (2) per car.
Hood to radiator weatherstrip
p/n: 60-0670-42
Weatherstrip or seal, hood panel to radiator support. Correct extruded rubber strip. Used on vehicles with factory A/C.
Hood To Radiator Weatherstrips
p/n: 60-0110-42
This Hood To Radiator Weatherstrip is sold as a pair for the right and left. Overall length is ten and seven-eighths (10-7/8") inches. Made of top-quality rubber to ensure durability and proper seal.
Hood Weatherstrip Clip
p/n: 70-1255-42
Clip, hood to cowl weatherstrip. Normal usage is fourteen (14) to sixteen (16) per car as needed.
Horn Button Contact Cushion
p/n: 60-0192-21
Cushion, standard steering wheel horn button contact. Two and one half (2-1/2) inch diameter.
Horn Button Contact Ring
p/n: 60-0157-21
Ring, horn button contact. Accessory banjo steering wheel. Four and one eighth (4-1/8) inch outside diameter.
Horn Button Contact Set
p/n: 60-0492-21
This is a three (3) piece Horn Button Contact set which is designed from the original part for superior fitment and function. Renews the operation of the steering wheel horn blowing ring.
Horn projector grommet
p/n: 60-0161-21
Grommet, horn trumpet through horn mounting bracket. For Deluxe country horn.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Inner Fender Filler
p/n: 60-0660-45
This Inner Fender Filler is designed from the original part for an authentic fit, finish, and appearance. Available by the foot.
Inner Fender Seal
p/n: 60-0667-45
Seal, inner fender to frame. Extruded rubber strip replacement. Available by the foot.
Inner Fender to Cowl Filler Set
p/n: 70-3356-45
This six (6) piece Inner Fender to Cowl Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit at rear of fender to cowl panel.
Inner Side Window Bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.
Kick Panel Vent Gaskets
p/n: 70-4919-88
This Kick Panel Vent Gasket pair is designed from the original part for superior fitment and function. Can be used on trucks with or without A/C.
Left Door Only Weatherstrip - Extended Cab Pickup
p/n: 70-4881-73
This Door Weatherstrip pair is designed from the original part for superior fitment and seal. Push-on type weatherstrip installs on the body of the driver side door on 3-door extended cab model pickups.
License Light Mounting Pad
p/n: 60-0099-17
This Rear License Light Mounting Pad is designed from the original part for an authentic fit, finish, and appearance. Length: 9 inches.
License Light Mounting Pad
p/n: 60-0074-17
Mounting pad, license light. Three and one eighth (3-1/8) inch by eight and seven eighths (8-7/8) inch. Fully detailed.Length: 8.875 inches.
License Light Mounting Pad
p/n: 60-0205-17
Mounting pad trunk license light. Not an original item. But many owners wish to pad this light from the paint job. Good fit, perfect bead form.
License Light Mounting Pad and Grommet Set
p/n: 60-0337-17
This License Light Mounting Pad and Grommet Set is designed from the original part for superior fitment and function. Mounting Pad for the license light to trunk lid. The Grommet is for the license bracket spacer post.
License Plate Light Lens Gasket
p/n: 70-3497-17
This License Plate Light Lens Gasket is designed from the original part for superior fitment and seal. This gasket fits between license plate light lens and housing.
License Plate Light Mounting Pads
p/n: 60-0174-17
This rear License Plate Light Mounting Pad pair is designed from the original part for superior fitment and function. This reproduction mounting pad fits between the rear License Plate Light Housing or Bezel and the vehicle body. Two (2) required per vehicle.
Liftgate Weatherstrip
p/n: 70-4122-85
This Liftgate Weatherstrip seal is designed from the original part for superior fitment and seal. The push-on style weatherstrip mounts on the upper portion of the body on liftgate models.
Liftgate Weatherstrip
p/n: 70-2090-85
This liftgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the liftgate with properly spaced plastic clips.
Liftgate Weatherstrip
p/n: 70-2148-84
This Liftgate Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the liftgate with properly spaced plastic clips.
Liftgate Weatherstrip
p/n: 70-3477-84
This Liftgate Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the liftgate opening directly to the body.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Lock Pillar Water Deflector
p/n: 70-3635-62
Door panel water deflector, at lock. Fully molded for both left and right hand sides.
Lower Control Arm Bushing Seal
p/n: 60-0095-32
This Lower Control Arm Bushing Seal is designed from the original part for superior fitment and seal. Installs at the lower control arm pivot bolt bushing. Four (4) per car.
Lower Door Weatherstrips
p/n: 60-0047-73
This Lower Door Weatherstrip pair is designed from the original part for superior fitment and seal. Each 36" length weatherstrip fastens to the cab threshold.
Lower Door Weatherstrips
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Lower Door Weatherstrips
p/n: 60-0313-73
This Lower Door Weatherstrip pair is designed from the original part for superior fitment and seal. Each weatherstrip is approximately thirty-two and one half (32-1/2) inches long and retained by a metal strip.
Lower Sash Channel Filler
p/n: 70-2844-57
This Lower Sash Channel Filler is designed from the original part for superior fitment and function. A flexible EPDM rubber extrusion that goes between glass and metal sash lift channel. Available by the foot.
Lower U-Jamb Lock Pillar Rear Seals
p/n: 70-3954-79
This Lower U-Jamb Lock Pillar Rear Seals pair, one for each door, is designed from originals and made for a like factory fit.
M6-1.0 Anchor Set - GM Vehicles
p/n: 70-4867-46
A top-quality neoprene rubber Well Nut, Washer and Screw Anchor for GM vehicle models. Well nut has a metric M6-1.0 captive brass nut. Overall length is 21/32". Replaces GM factory number #20130258.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32") inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons and other project uses.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
One-Piece Windshield Reveal Molding
p/n: 70-4289-52
This three (3) sided, One-Piece Windshield Reveal Molding is designed from the original part for superior fitment. This part fits across the top and on each side of the windshield. The part is made with top quality materials and with the proper molding profile for an exact fit and finish.
Outer Beltline Scraper Weatherstrips
p/n: 50-0455-61
This Outer Beltline Scraper Weatherstrip pair is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door.
Outer Beltline Weatherstrip
p/n: 70-0879-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 70-0784-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 50-0488-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Front Header Weatherstrip
p/n: 70-4834-68
This removable hardtop Outer Front Header Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip installs on the front of the shell with weatherstrip adhesive glue (not included) and presses against the cab weatherstrip. This single piece is for the double wall hardtop models.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
Paint Gasket Set
p/n: 82-0224-44
This comprehensive fifteen (15) piece Paint Gasket Set includes the major seals and gaskets when painting or restoring a classic Camaro. These reproduction parts are designed from originals for superior performance, durability and a factory like fit.