Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Trunk handle mounting pad
p/n: 70-2025-86
Pad, trunk handle to trunk lid. Fully molded with proper retaining lip, two (2) piece set.
Fuel Filler Neck Grommet
p/n: 60-0434-41
This Fuel Filler Neck Grommet is the inner grommet through the quarter panel inside fuel filler door. Fully molded rubber with retaining flange as original for good seal. Three and one eighth inch (3-1/8") outside diameter by two and one eighth inch (2-1/8") inside diameter.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Taillight Gasket
p/n: 60-0693-15
Seal, taillight bezel. Correct profile and long lasting material. Six (6) strips cut twelve and three fourths (12-3/4) inches long.Length: 12.75 inches.
Taillight Gasket
p/n: 60-0691-15
This Taillight Gasket is made of fully molded soft-dense rubber compound to ensure proper installation and performance. Designed from the original part for the correct profile. Two (2) strips cut thirty-six (36) inches long.
Upper Door Weatherstrip - Left or Right
p/n: 70-4880-73
This Upper Door Weatherstrip is made from high-quality ozone-resistant PVC rubber. This single piece weatherstrip is installed onto the A-pillar, spanning along the upper section of the cab opening and extending down the rear side door of the 4-door trucks.
Taillight Mounting Pad
p/n: 60-0545-15
Pad, bracket mounting to body for tail and license plate light. Length: 3.3125 inches. Width: 2.5625 inches.
Fuel Neck Grommet
p/n: 60-0149-41
Grommet, fuel filler neck (1955-1st type). Oblong fully molded rubber with retaining flange. Three and seven eighths inch (3-7/8") outside width by five and one eight inch (5-1/8") outside length by one and one eighth inch (1-1/8") height.
Horn projector grommet
p/n: 60-0161-21
Grommet, horn trumpet through horn mounting bracket. For Deluxe country horn.
Floor Shift | Carpet Grommet
p/n: 70-3265-88
This Floor Shift / Carpet Grommet is designed from the original part for superior fitment and seal. This part seals the carpet edge to the floor shift boot. For models without floor console.
Fuel Neck Grommet
p/n: 60-0474-41
Grommet, fuel filler neck. Fully molded rubber. Three and one fourth inch (3-1/4") outside diameter by two and one half inch (2-1/2") inside diameter.
Choke Cable Support Grommet
p/n: 60-0373-13
Grommet, choke cable support-at-ignition cable.Width: 1.25 inches.
Exhaust System Hanger
p/n: 60-0307-13
This Exhaust System Hanger is used for the muffler-to-tailpipe support (insulator) with reinforced webbing. Fully molded from top-quality EPDM dense rubber to ensure durability. One (1) required per car.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Taillight Lens Gasket
p/n: 60-0175-15
Gasket, taillight lens.Length: 3.50 inches. Width: 2.25 inches.
Cowl Vent Gasket
p/n: 60-0087-54
Gasket, cowl vent, lip type. Sponge rubber, for three and seven eighths (3-7/8) inch by fifteen (15) inch cowl vent.Length: 15.0 inches. Width: 3.
Hood to Cowl Rear Weatherstrip
p/n: 70-4692-43
This Hood To Cowl Rear Weatherstrip is designed from the original part for superior fitment and seal. A reproduction manufactured to the original profile and design specifications. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 70-3448-42
This Hood to Cowl weatherstrip is for superior fitment and sealing. This extruded sponge rubber clinch seal strip mounts at the rear of the engine bay directly to the body on the cowl lip.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Cowl Vent Gasket
p/n: 60-0131-54
Gasket, cowl vent. One fourth (1/4) inch by five sixteenths (5/16) inch, for five (5) inch by fifteen (15) inch top cowl vent. Sponge type.Width: 15.
Door Bumper
p/n: 60-0334-71
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.