Side Window Header Channel
p/n: 70-0306-58
Plush lined rubber channel for across top of doors above side windows on closed bodies. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Parking Light Lens Gasket Set
p/n: 70-4463-36
This Parking Light Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the Parking Light Lens and the Parking Light Housing or Bezel.
Door Alignment Pad
p/n: 60-0060-71
Wedge pad, door aligning dovetail. Goes under bumper retainer.Length: .9375 inches. Width: .9375 inches. Height: .4375 inches.
Handbrake Lever Anti-Rattle
p/n: 60-0531-24
Spacer, anti-rattle, handbrake lever sector rod, between release rod and handbrake lever.Width: .6875 inches. Height: .6875 inches.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Cowl Panel to Cowl Filler Seals
p/n: 70-3695-43
This Cowl Panel to Cowl Filler Gasket pair is designed from the original part for superior fitment and function. These seals go under the cowl vent grille on the left and right sides of it.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Engine Mounting Pad
p/n: 50-0229-11
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Windshield Post Bumper
p/n: 33-0037-52
Bumper, windshield post (side arm). Replaces #366138. Two (2) per car.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Taillight Lens Gaskets
p/n: 70-4170-15
This six (6) piece Taillight Lens Gasket set is a die cut sponge rubber gaskets made to authentic original dimensions. Includes right and left side gaskets. This reproduction gasket fits between taillight lens & taillight housing.
Steering Column At Floor Seal
p/n: 70-3490-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. The seal is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
1-13/16" Trunk Floor Pan Plug
p/n: 70-2599-87
This Trunk Floor Pan Plug is designed from the original part for superior fitment and seal. This plug is made from high quality EPDM dense rubber to provide excellent durability.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Parking Brake Pedal Pad
p/n: 70-4804-22
This reproduction Parking Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace a worn or damaged original pedal pad.
1-5/16" Firewall Grommet
p/n: 32-0347-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for wiper control cable and heat tube.
Tailgate Handle Gasket
p/n: 70-3867-86
This Tailgate Handle Gasket is die-cut sponge rubber to authentic original dimensions.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
Windshield Bumpers - Steel Core
p/n: 34-0258-52
Bumper (stop), swing out windshield against dash. Steel core, nine sixteenths (9/16) inch diameter by five sixteenths (5/16) inch thick. Replaces #3681093. Two (2) per vehicle.
1-3/16" Firewall Grommet
p/n: 32-0394-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Kick Panel Vent Gaskets
p/n: 70-4919-88
This Kick Panel Vent Gasket pair is designed from the original part for superior fitment and function. Can be used on trucks with or without A/C.
1-11/16" Main Harness Firewall Grommet
p/n: 70-2606-20
This Firewall Grommet fits to the engine firewall where main wire harness plugs in. Designed from the original part for superior fitment and finish.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.
Taillight Lens Gasket Set
p/n: 70-4916-15
This Taillight Lens Gasket set is designed from the original part for superior fitment and seal. Six (6) reproduction gaskets fit between taillight lens and taillight housing bezel.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Rear Spring Eye Bushing
p/n: 60-0208-32
This Rear Spring Eye Bushing pair is designed from the original part for superior fitment and function. Bushings are for the rear spring, shackle eye, and spring eye. Up to twelve (12) per car.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
2-1/4" Trunk Floor Pan Plug
p/n: 70-2598-87
This Trunk Floor Pan Plug is designed from the original part for superior fitment and seal. This plug is made from high quality EPDM dense rubber to provide excellent durability.
Taillight Lens to Bezel Gaskets
p/n: 70-4464-69
This Taillight Lens to Bezel Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens and taillight housing bezel.
Body Mounting Pad
p/n: 40-0324-48
Cushion, used as either a body mounting pad or for all body bolt nuts, below brackets. Fully molded rubber. Two inch (2") outside diameter by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Trunk Deck Lid Rubber Bumpers
p/n: 70-2601-42
This Trunk Deck Lid Rubber Bumper pair is designed from the original part for superior fitment, finish and function. The correct OE style trunk deck lid rubber bumpers stoppers. Two required per car.
Door Bumper
p/n: 60-0048-71
Bumper, door side. Five eighths (5/8) inch by seven eighths (7/8) inch by one and seven sixteenths (1-7/16) inch. Two (2) door.
Rear Shock Absorber Link Bushing
p/n: 60-0521-33
This Rear Shock Absorber Link Pin Bushing is designed from the original part for superior fitment and function. Four (4) per car for double action shocks.
Taillight Housing to Body Seals
p/n: 70-3488-15
This Taillight Housing to Body Seal pair is designed from the original part for superior fitment and seal. These reproduction seals fits between the taillight housing and the vehicle body.
Steering Column - Floor Seal
p/n: 70-3499-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Fresh Air Vent Door Seals
p/n: 70-4166-88
This two (2) piece Fresh Air Vent Door Seal pair is designed from the original part for superior fitment and seal. Seal pieces are manufactured from top quality sponge rubber to original specifications.
Tailgate Bumper
p/n: 70-1910-87
This Tailgate Bumper is designed from the original part for superior fitment, finish and function. This station wagon tailgate bumper is commonly used on GM station wagon models.
Door Handle Gasket Set
p/n: 60-0352-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Wiring Harness Loom Grommet
p/n: 60-0255-14
This Grommet is designed from the original part for superior fitment. The grommet ideally works for the headlight or taillight wiring loom through body sheet metal. Four (4) to six (6) grommets per vehicle.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Taillight Lens Gasket Set
p/n: 70-4914-15
This Taillight Lens Gasket set is designed from the original part for superior fitment and seal. Six (6) reproduction gaskets fit between taillight lens and taillight housing bezel.
2-7/16" Floor Plug
p/n: 35-3508-45
This Floor Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to ten (10) used per vehicle.
Wiper Transmission To Cowl Gaskets
p/n: 60-0101-53
This Wiper Transmission To Cowl Gasket pair is designed from the original part for superior fitment and seal. Gaskets are precision die cut from quality dense rubber material.
Wiper Transmission Gasket
p/n: 60-0029-53
Gasket, windshield wiper transmission mounting. Replaces #4073727.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.
Door Handle Gasket Set
p/n: 60-0673-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Wiper Transmission Gasket
p/n: 27-0052-53
Gasket, windshield wiper transmission made of the highest quality and authenticity. Replaces #4562197.
Bumper Support Bar Pad
p/n: 60-0544-30
A fully molded rubber Bumper Support Bar Pad. Thes part installs between the bumper support bar and bumper face bar at the mounting bolts. Use as required, eight (8) are needed for most cars.
Wiper Transmission Gasket
p/n: 60-0402-53
Gasket, windshield wiper transmission mounting. Replaces #4597009. Two (2) required per car.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Steering Column Gasket
p/n: 60-0435-32
This Steering Column Gasket is designed from the original part for superior fitment and sealing. Gasket is die cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Door Handle Gasket Set
p/n: 60-0541-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Splash Apron / A-Arm Dust Shield Set
p/n: 70-4042-45
This two (2) piece Splash Apron / A-Arm Dust Shield Set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Splash Apron / A-Arm Dust Shield Set
p/n: 70-4041-45
This two (2) piece Splash Apron / A-Arm Dust Shield Set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Splash Apron / A-Arm Dust Shield Set
p/n: 70-4040-45
This two (2) piece Splash Apron / A-Arm Dust Shield Set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Wiper Cowl Weatherstrips
p/n: 70-4882-43
This Wiper Cowl Weatherstrip pair is designed from the original part for superior fitment and seal. This is the rear outer wiper cowl pair. These weatherstrips sit behind the hood to cowl primary weatherstrip by the left-side and right-side hood hinges.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Convertible Top Arm Cover Caps
p/n: 70-0736-67
This four (4) piece Convertible Top Arm Cover Cap set is designed from the original part for superior fitment, finish and function. Installs on the folding pillar to side roof rail links. A perfect copy in original grey rubber. Four (4) piece set.Length: 1-3/4" inches.
Splash Apron / A-Arm Dust Shield
p/n: 70-2507-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Steering Column - Floor Seal
p/n: 70-3358-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Hood To Fender Bumper
p/n: 60-0318-42
This Hood To Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle, order as needed.
Taillight Housing To Body Seals
p/n: 70-4171-15
This six (6) piece Taillight Housing To Body Seal set is designed from the original part for superior fitment and seal. These authentic reproduction seals fit between the taillight housing and the vehicle body.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Steering Column At Floor Seal
p/n: 70-4629-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. This gasket is manufactured from top quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Steering Column At Floor Seal
p/n: 70-4630-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. This gasket is manufactured from top quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Parking Light Lens Gasket
p/n: 60-0470-17
Gasket, parking light lens. One and one half (1-1/2) inch by four (4) inch.1941: All commercial and utility 1942: Most models Length: 4.0 inches.
1-11/16" Firewall Grommet
p/n: 32-0160-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Body Mounting Pad
p/n: 60-0027-48
Pad, side body mounting. Fully molded rubber, rectangular. Two and seven-sixteenths inch (2-7/16") outside length by one and five-eights inch (1-5/8") outside width by one-fourth inch (1/4") height.
Rear Liftgate Bumpers
p/n: 70-4833-87
This fully molded Rear Liftgate Bumper pair is a quality reproduction of the original factory part. These two (2) rubbers bumpers attach to the vehicle rear liftgate to support / cushion the liftgate closure.
Steering Column Vacuum Shift Cylinder Boot
p/n: 60-0556-24
This Steering Column Vacuum Shift Cylinder Boot is designed from the original part for superior fitment, function and appearance. Perfectly engineered duplicate of original. Constructed of durable long lasting rubber. Length: 4-3/8" inches.
Taillight Gasket
p/n: 60-0697-15
Seal, taillight bezel. Correct profile and long lasting material. Four (4) strips cut sixteen and three eighths (16-3/8) inches long.
Antenna Mount Pad
p/n: 60-0050-21
This Antenna Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and fender to protect the surface.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Taillight Housing To Body Gasket Set
p/n: 70-4915-15
This Taillight Housing To Body Gasket Set is designed from the original part for superior fitment and sealing. These six (6) reproduction gaskets fit between taillight frame housing and the body.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.