Retractable Headlight Seal
p/n: 20-0144-14
Seals, headlight opening cover plate. With headlight covers.
Hood Bumper
p/n: 20-0211-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Hood Bumper
p/n: 20-0209-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Radiator Shroud Seal
p/n: 20-0191-31
Seal, radiator side air deflector. Three (3) inch by fourteen and one eighth (14-1/8) inch.
Parking Light Lens Gaskets
p/n: 20-0166-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Steering Column Floorplate
p/n: 20-2646-88
Seal, standard trans. steering post to floor. Installs under metal plate.
Taillight Lens Gaskets
p/n: 20-1229-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing bezel.
Steering Column Lower Flange Insulator
p/n: 20-1532-88
This Steering Column Lower Flange Insulator is designed from the original part for superior fitment and function. This insulator fits around the lower steering column inside the vehicle to prevent metal to metal contact.
Quarter Panel Drain Plugs
p/n: 20-2769-45
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
Splash Apron
p/n: 20-2508-45
This Splash Apron is designed from the original part for superior fitment and seal. Seals the lower front splash pan to the bottom of the radiator.
Spring Shackle Bushing Set
p/n: 20-2481-33
This Spring Shackle Bushing Set is for the front of the rear leaf spring. Two (2) kits required per car.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Radiator Shroud Seal
p/n: 20-0182-31
Seal, radiator side air deflector. One and five eighths (1-5/8) inch by twelve and one half (12-1/2) inch.
Parking Light Assembly Mounting Pads
p/n: 20-2426-16
This Parking Light Assembly Mounting Pad pair is designed from the original part for an authentic fit, finish, and appearance. These mounting pads fit between the park light assembly and fender.
Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
Ventilator Air Inlet Duct Door Gaskets
p/n: 20-1827-31
This Ventilator Air Inlet Duct Door Gasket pair is designed from the original part for superior fitment and seal. These gaskets seal between the ventilator air inlet duct door to the duct inside.
Wiper control grommet
p/n: 20-2526-53
Gaskets, wiper pivot spacer to body. Replaces factory #8A-17541-B.
Front Bumper Grommet
p/n: 20-2509-45
Grommets, front stone deflector to bumper arm anti-rattler. Two and one fourth (2-1/4) inch long. Two (2) piece set.
Main Wiring Loom Grommet
p/n: 20-2433-20
This Main Wiring Loom Grommet is used to protect the wiring from the sheet metal of the firewall. Made from high-quality dense rubber to provide excellent durability.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Antenna to Front Fender Mount Pad
p/n: 20-1809-19
This Antenna to Front Fender Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and top of front fender to protect the painted surface.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Front suspension bushing
p/n: 20-2471-32
Seal, front suspension. Inner upper arm.Qty Required:4 Four (4) required per car.
Front suspension bushing
p/n: 20-2474-32
Seal, front suspension lower control arm outer. Four (4) required per car.
Taillight Lens Gasket
p/n: 20-1988-15
Gasket, taillight lens. Inner and outer seal. Enough for one taillight lens.
Rear Spring Pad
p/n: 20-1275-32
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Front Fender Pads
p/n: 20-1866-45
This Front Fender Pad pair is designed from the original part for superior fitment and seal. These weatherstrip pads fit at the top rear of the front fender to cowl panel.
Wiper Hose Grommet
p/n: 20-2524-53
This Wiper Hose Grommet is used to protect the wire when running it through the firewall. Designed from the original part for superior fit and seal.
Wiring grommet
p/n: 20-1801-17
Grommet, license plate light wire. Installs where wire comes in rear bottom of trunk.
Wiper control grommet
p/n: 20-2525-53
Gaskets, wiper pivot spacer to body. Replaces factory #8A-17541-A.
Speedometer Cable Grommet
p/n: 20-2435-20
This Speedometer Cable Grommet is used to protect the cable when running it through the firewall. Designed from the original part for superior fit and seal.
Air Vent Cable Grommet
p/n: 20-2437-20
This Air Vent Cable Grommet is used where the air cable passes through the firewall. One pair required per vehicle. This grommet is also commonly used for the hood pull cable, heater wire, and electric wiper motor cable.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Front suspension bushing
p/n: 20-2470-32
Seal, front suspension. Inner lower arm.Qty Required:4 Four (4) required per car.
Hood To Radiator Weatherstrip
p/n: 20-2468-31
This Hood To Radiator Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal functions as a radiator air deflector by mounting to the top of the radiator.
Accelerator Pedal Rod Seal
p/n: 20-1448-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from original part so it fits correctly.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Radiator mounting pad
p/n: 20-1873-48
Pads, radiator support to frame. One upper & one lower. Two (2) required per car.
Shock Absorber or Track Bar Bushing
p/n: 20-2476-33
This Shock Absorber or Track Bar Bushing is designed from the original part for superior fitment and function. These bushes are used on tubular-style shock absorbers and also on stabilizer track bar(s).
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.