Windshield Wiper Hose Grommet
p/n: 20-1611-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from original part so it fits correctly.
Wiper Hose Grommet
p/n: 20-2206-53
This Wiper Hose Grommet is used where the wiper hose and temperature gauge wire go through the firewall. The grommet can also be used where the headlight bucket wires go through the inner fender.
AC Condenser Tube to Radiator Support Grommet
p/n: 20-2724-31
This A/C Condenser Tube to Radiator Support Grommet is used to protect the air conditioner condenser tubes to the radiator support. Designed from original part so it fits correctly.
AC Condenser Tube to Radiator Support Grommet
p/n: 20-2723-31
This A/C Condenser Tube to Radiator Support Grommet is used to protect the air conditioner condenser tubes to the radiator support. Made from flat foam rubber to provide protection.
Accelerator Pedal Rod Firewall Grommet
p/n: 20-2744-41
This Accelerator Pedal Rod Firewall Grommet is used to run the accelerator pedal rod through the firewall. Designed from original part so it fits correctly.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Front fender center pad
p/n: 20-1865-45
Pads, back center of front fender. Mounts where fender bolts to cowl.
PCV valve grommet
p/n: 20-2696-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
Door Glass Bumper
p/n: 20-1170-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Door Glass Bumper
p/n: 20-1172-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Door Glass Bumper
p/n: 20-1171-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Tailgate Side Seals
p/n: 70-4009-85
This Tailgate Side Seals includes right and left side with installation screws. These seals are properly molded from originals for a factory like fit.
Choke and Throttle Dash Grommets
p/n: 20-0347-41
This Choke and Throttle Dash Grommet pair mounts in the dash where the choke and throttle rods pass through the dash to keep rods from rattling.
Front Fender Plugs
p/n: 20-0753-20
This Front Fender Plug pair is a reproduction manufactured to OEM specifications to install for an authentic fit and finish. Used on the top of the front fender towards the rear to help reduce heat and fumes from entering the cab.
Body Hole Plug
p/n: 20-0845-20
Plug, oval floor pan front. Rubber. One half (1/2) inch by one (1) inch diameter. Two (2) each required per truck.
Body Hole Plug
p/n: 20-0843-20
Plug, style-side bed side panel. One and five eighths (1-5/8) inch diameter. Fits 1-1/16" hole.
Body Hole Plug
p/n: 20-0844-20
Plug, cowl side panel inner. One and seven eighths (1-7/8) inch diameter. Two (2) each required per truck.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Front suspension bushing
p/n: 20-2473-32
Seal, front suspension outer upper arm. Four (4) required per car.
Glovebox Arm Bumper Stop
p/n: 20-1399-88
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Hood bumper
p/n: 20-1309-42
Bumper, hood pull cam. Two (2) required per car.Ford Cars 1957-60 Bumper, hood pull cam. 2 required per car. Ford Cars 1958-59 Bumper, trunk lid.