Door Drain Hole Seal
p/n: 70-1042-70
Weatherstrip, door bottom drain hole.Length: 3.625 inches. Width: .40625 inches.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Hinge Seals
p/n: 70-1460-70
This Door Hinge Seal installs on the front door hinge pillar at the beltline. These seals are sold as a pair for the left and right side.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Firewall Grommet
p/n: 25-0099-20
This Firewall Grommet is used to run accessory wiring through the firewall. Designed from the original part for superior fit and seal.
Front Door Lock Pillar Filler
p/n: 70-0834-79
This Front Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler seals the bottom at the front of the rear side window. Also known as a door jamb seal.
Front Door Vent Window Weatherstrip Set
p/n: 90-0426-90
This four (4) piece Front Door Vent Window Weatherstrip Set contains the main vent window and division post weatherstrips. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0092-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Weatherstrips
p/n: 70-0825-72
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes six (6) clips for easy installation. Made of top quality rubber.
Front Engine Support Insulator
p/n: 25-0041-11
This Front Engine Support Insulator is designed from original for an exact aftermarket replacement.
Fuel Filler Neck Grommet
p/n: 70-1439-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fits as original.
Hardtop Roof Rail Weatherstrips
p/n: 50-0460-68
This Hardtop Roof Rail Weatherstrip pair fits on the roof of the vehicle and seals the side window when the window is fully raised. These Weatherstrips are made of ozone resistant EPDM sponge rubber with molded A pillar ends for a factory like fit.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Bumper
p/n: 25-0076-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Radiator Mounting Pad
p/n: 25-0087-31
Insulator, radiator support. Two (2) to four (4) used per car.Length: 6.75 inches.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Rear Door Pillar Filler
p/n: 70-0837-79
This Rear Door Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a door jamb seal.
Rear Door Weatherstrips
p/n: 70-0901-72
This Rear Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (pin-on) directly to the left and right rear doors sealing the doors against the vehicle body when the door is closed.
Rear Window Gasket
p/n: 50-0387-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.