Gearshift Boot
p/n: 20-2878-88
Boot, 4-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Brake Cable Anti-Rub Cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Brake Cable Boot
p/n: 60-0156-24
Boot, front brake cable end at brake backing plate. Two and seven eighths (2-7/8) inches long.Length: 2.875 inches.
Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Clutch Control Boot
p/n: 30-0273-24
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with Electromatic
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Brown gearshift boot
p/n: 30-0129-89
Boot for column gearshift, short type. Brown rubber. For black see our #30-0129-24. All series with column shift.Color:brown Length: 1.
Brake Cable Boot
p/n: 60-0155-24
Boot, rear, brake cable end at brake backing plate. Three and one half (3-1/2) inches long.Length: 3.50 inches.
Clutch Release Lever Boot
p/n: 20-0761-24
This Clutch Release Lever Boot is designed from the original part for superior fitment and seal. This boot is for the clutch release lever to clutch housing.
Brown Gearshift Boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Brake and clutch shank seal
p/n: 70-0192-23
Grommets, clutch and brake pedal shank. Hollow accordion action type, not a sponge ring.
Gearshift Boot
p/n: 30-0412-24
Grommet, shifter shaft to shroud. One (1) per car.Length: 4.125 inches. Width: 2.3125 inches.
Brake and clutch shank seal
p/n: 20-0758-23
Seal, clutch rod to floor. Useage: 1971-72: F100-350 series AFTER Serial #M00,001 1973-79: F100-350 series trucks
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Gearshift Floorplate
p/n: 20-0464-88
Seals, transmission cover to floor. Cork and rubber. Three (3) piece set.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Brake and Clutch Pedal Bumper
p/n: 60-0024-24
Bumpers, brake and clutch pedal shank to floorboard. Rides pedal shank under floorboard.
Gearshift Knob
p/n: 20-0763-24
This black column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Gearshift Boot - At Floor
p/n: 60-0108-24
This Gearshift Boot is designed from the original part for superior fitment and function. Cup style boot to fit over the gear shifter stick at the floorboard.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
Gearshift Boot
p/n: 50-0035-24
Boot, gearshift. Black rubber. For brown see our #50-0035-89.Width: 2.8125 inches.
Gearshift Boot
p/n: 30-0129-24
Boot for column gearshift, short type. Black rubber. For brown see our #30-0129-89. All series with column shift.Height: 1.4375 inches.
Gearshift Gasket
p/n: 60-0397-24
This sponge rubber Gearshift Gasket is one-half (1/2) inch thick. For the gearshift at floorboard. One required per vehicle.
Brake and Clutch Shank Seal
p/n: 12-0006-24
Seal, brake and clutch pedal shank to floorboard. Three eighths (3/8) inch thick, two and one half (2-1/2) inch diameter.
Clutch Rod Boot
p/n: 20-2949-23
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Brake and Clutch Shank Seal
p/n: 70-0962-23
Grommet, brake or clutch shaft at toe board.Height: 1.0 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Brake and clutch shank seal
p/n: 70-0466-23
Grommet, brake and clutch pedal shank above floorboard. Special offset pattern as original.
Brake and Clutch Shank Seal
p/n: 40-0355-24
Seal, brake and clutch pedal below floorboard. Two (2) per car.Length: 2.75 inches. Width: 1.9375 inches.
Brake and clutch shank seal
p/n: 20-0850-23
Seal, clutch rod to floor. Rubber with metal. Useage: 1968-71: F100-350 Series before Serial #M00,001.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Floor Shift | Carpet Grommet
p/n: 70-3265-88
This Floor Shift / Carpet Grommet is designed from the original part for superior fitment and seal. This part seals the carpet edge to the floor shift boot. For models without floor console.
Handbrake and Gearshift Pad
p/n: 50-0247-24
Pad, handbrake and gearshift floorplate. Pad goes only under handbrake area, as original.
Black Gearshift Boot - Steering Column
p/n: 30-0069-36
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Black rubber. Two and one quarter (2-1/4) inches long.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Clutch and Brake Pedal Bumpers
p/n: 60-0579-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. This pedal to floorboard bumper is the longer type with one and three-eighths (1-3/8") inch clearance for the pedal shaft.
Gearshift Boot
p/n: 70-2285-26
Boot, transmission control shift lever. Fully molded out of black rubber instead of original white rubber, though it could be painted like original. For vehicles with Hydra-Matic column shift
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Steering column seal
p/n: 60-0478-36
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Gearshift Grommet
p/n: 40-0075-88
Grommet, gearshift lever, small type. Five eighths (5/8) inch inside diameter.
Vacuum Cylinder Seal
p/n: 30-0203-24
Seals, actuating valve rod, brake and clutch vacuum cylinder.Width: .875 inches.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Clutch Pedal Bumper - Under Floorboard
p/n: 60-0355-24
This Clutch Pedal Bumper is designed from the original part for superior fitment and function. This clutch pedal shank bumper fits under vehicle floorboard.
Clutch Lever Dust Boot
p/n: 70-4760-24
This Clutch Lever Dust Boot covers the opening on your engine bellhousing for manual transmission models. A reproduction manufactured to OEM specifications to install for an authentic fit, finish and function.