Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
1/2" Convertible Rail Grommet
p/n: 32-0132-67
This Convertible Rail Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the upper side rail when the rails are removable.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Trunk Bumper
p/n: 20-1923-67
Bumpers, package tray panel. Glues on bottom of trunk lid door where front of package tray panel contacts bottom of trunk lid.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Trunk Hinge Gaskets - Convertible
p/n: 70-4657-87
This Trunk Hinge Gasket pair is designed from the original part for superior fitment, finish and function. On Convertibles the gasket pair install between the plastic hinge cover and the trunk lid on the exterior (near the rear window).
Convertible Top Arm Cover Caps
p/n: 70-0736-67
This four (4) piece Convertible Top Arm Cover Cap set is designed from the original part for superior fitment, finish and function. Installs on the folding pillar to side roof rail links. A perfect copy in original grey rubber. Four (4) piece set.Length: 1-3/4" inches.
Retractable Roof Bumpers
p/n: 20-1930-67
This Retractable Roof Bumper pair is designed from the original part for superior fitment and function. This fits the front roof to rear roof on retractable convertibles.
Convertible Top Weatherstrip Fastener Set
p/n: 70-4759-67
This sixteen (16) piece Convertible Top Weatherstrip Fastener Set is designed from the original part for superior fitment, finish and function. An exact copy of originals. The set includes 16 zinc plated special tube nuts and 16 special washers.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Retractable roof weatherstrip
p/n: 20-1926-67
Weatherstripping, rear roof front. This is the seal between front part of rear top and flapper.
Finish Panel To Package Tray Weatherstrip
p/n: 70-3874-87
This Rear Finish Panel to Package Tray Weatherstrip attaches to the trunk body and seals between the finish panel and the package tray near the convertible top when closed.
Rear Seat Back Finish Panel to Package Tray Weatherstrip
p/n: 70-4096-87
This Rear Seat Back Finish Panel To Package Tray Weatherstrip mounts directly to the body to seal the Rear Seat Back Finish Panel to the Package Tray.
Decklid Top Cover Weatherstrip
p/n: 70-3922-67
This Decklid Top Cover Weatherstrip is designed from the original part for a superior fitment and seal. This weatherstrips mounts around the full perimeter of the soft top storage compartment.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Hydraulic Pump Mounting Pad
p/n: 70-0986-62
Mounting bracket and pad, for hydraulic pump. Number used as required.Length: 1.75 inches. Width: .8125 inches.
Hydraulic Pump Mounting Pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Convertible Top Latch Catches and Guides Set
p/n: 70-4655-67
This Convertible Top Latch Catches and Guides Set is an important maintenance piece on Mustang and Cobra models with a convertible top. Replace your cracked j-hook and broken dowel pin receptacles with this quality reproduction four (4) piece set.
Retractable roof weatherstrip
p/n: 20-1921-67
Pads, flapper. (Front of top rests on when top is down.) Glues to top of wheel well.
Detachable Centerpost Pads
p/n: 30-0108-67
This Detachable Centerpost Pad pair is designed from the original part for an authentic fit and finish.
Windshield Trim To Glass Weatherstrips - Convertible
p/n: 70-4660-52
This Windshield Trim To Glass Weatherstrip pair for convertibles is designed from the original part for superior fitment, finish and function. These LH and RH windshield trim weatherstrips go between the windshield and the windshield molding.
Convertible Top Rail Cushions
p/n: 70-3438-67
Convertible top cushion pads. These parts go between the first & second section of the roof rail for both the left and right sides.
Convertible Top Rail Drains
p/n: 20-1157-67
This Convertible Top Rail Water Drain pair is designed from the original part for superior fitment and function. The part fits on the convertible top rail at the rear as a water drain.
Convertible Top Pads
p/n: 20-1158-67
This Convertible Roof Top Pad pair is designed from the original part for superior fitment and function. The part fits at the top of the rear quarter window on the roof.
Convertible Roof Rail Bumper
p/n: 20-1920-67
Bumpers, roof assembly to quarter panel. Four (4) piece set.
Convertible Weatherlip
p/n: 70-0616-67
Weather deflector, edge of folding top fabric near folding post, mounted on body.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Convertible Roof Rail Weatherstrip T-Bolt Set
p/n: 70-4606-67
These Convertible Top Roof Rail Weatherstrip T-Bolt reproductions are designed from the original part for superior fitment and function. This twenty two (22) t-bolts and twenty two (22) nut set fastens to the convertible top bow weatherstrips.
Top Motor Grommet Set
p/n: 20-1637-67
This Top Motor Grommet Set contains three (3) pieces that are used for the top motor to the firewall bracket. Designed from the original part for superior fit and seal.
Convertible Top Rear Rail Water Deflector
p/n: 20-0028-67
This Convertible Top Rear Rail Water Deflector pair is designed from the original part for superior fitment and seal. For soft folding tops the deflector pair is included in Convertible Roof Rail Weatherstrip sets 20-0027-65 and 20-0139-65.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Retractable Hardtop Front Panel Rear Weatherstrip
p/n: 20-1935-67
This Retractable Hardtop Front Panel Rear Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip fits at the rear of the front panel of the retractable hardtop. Has special molded ends.
Convertible Top Decklid Weatherstrip
p/n: 70-3950-67
This Convertible Top Decklid Weatherstrip is designed from the original part for a superior fitment and seal. This rubber seal mounts around the full perimeter of the soft top storage compartment.
Convertible Post Bumper
p/n: 30-0409-67
Bumper, convertible top side roof rail, center. Two (2) per car.
Convertible B-Pillar End Cap Fillers
p/n: 70-4192-63
This Convertible B-Pillar End Cap Filler pair is designed from the original part for superior fitment and sealing. This rubber filler pair attaches to the body B-Pillars to seal between that quarter post and the door when closed.
Detachable Center Post Pad
p/n: 30-0422-67
Pad, convertible top center latch. Excellent workmanship with metal insert like original.
Retractable roof weatherstrip
p/n: 20-1922-67
Seals, body to rear side of top. Glues to top of quarter where sides of top set on body when top is up.
Convertible Top - Rest Block
p/n: 50-0318-67
Rest block, convertible top. Two (2) required per car. Fits into dovetail retainer. Length: 1.375 inches. Width: 1.125 inches.
Convertible Top - Resting Block
p/n: 20-2231-67
Pad, convertible top resting block. Used when top is down. One (1) required per vehicle.
Convertible Top Deck Lid Cover Weatherstrip
p/n: 70-3939-67
This Convertible Top Deck Lid Cover Weatherstrip is designed from the original part for a superior fitment and seal. This rubber seal mounts around the full perimeter of the soft top storage compartment.
Convertible Front Roof Rail Weatherstrip
p/n: 70-4189-67
This Convertible Front Roof Rail Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrip pair installs directly to the front section of the roof rails on the convertible top.
Convertible Top Rest Block
p/n: 60-0209-67
These Convertible Top Rest Blocks are used on the folding top, side roof rail slat iron. Fully molded with a brass core as original. Sold as a pair. Two (2) or four (4) per car as required for front and center.
Convertible Rear Roof Rail Weatherstrip
p/n: 70-4191-67
This Convertible Rear Roof Rail Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrip pair installs directly to the rear section roof rails on the convertible top.
Convertible Center Roof Rail Weatherstrip
p/n: 70-4190-67
This Convertible Center Roof Rail Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrip pair installs directly to the center section roof rails on the convertible top.
Stirrup Pad - Folding Top Bows
p/n: 10-0138-67
Stirrup Pad for folding top bows. This part is compatible with certain Sterns-Knight and (1916) Oldsmobile 44 V8 models.
Convertible Quarter Window Top Frame At Beltline Seals
p/n: 70-4545-61
This Convertible Quarter Window Top Frame At Beltline Seal pair is designed from the original part for superior fitment and seal. This seal fills the gap where the top, beltline moulding and the quarter window meet. A quality manufactured reproduction.
Retractable roof weatherstrip
p/n: 20-1927-67
Weatherstripping, rear roof side. Glues on top of rear quarter.
Quarter Window Weatherstrip End Fillers
p/n: 70-4711-79
This Quarter Window Weatherstrip End Filler pair is designed from the original part for an authentic fit, finish, and function. Filler strips install at rear on inner panel at back end of the quarter window beltlines on convertible models.
Convertible Roof Rail Bumper
p/n: 70-0976-67
Bumper, folding top side roof rail at quarter window. Made with metal core like original.
Quarter Window Filler
p/n: 70-3431-67
These quarter window fillers mount inside the rear panel at the bottom of the rear side window. The pair is fully molded as left and right with brass cores.
Front Bow Corner Filler
p/n: 70-0975-67
Filler, front corner of convertible top front bow. Made from soft durable rubber. Includes separate brass retainers.
Convertible Top - Arm Pad
p/n: 50-0319-67
Bottom pad, right and left side for 3rd bow folding post. Steel core with all original features. Quality rubber.
Convertible Roof Rail Bumper
p/n: 70-1023-67
Bumper, convertible top. Fully molded with threaded metal core. Excellent quality.
Detachable Center Post Pad
p/n: 30-0408-67
Pad, detachable center post, right and left hand.Width: 2.125 inches. Height: 2.6875 inches.
Luggage Compartment Door Bumper
p/n: 70-4143-87
This Luggage Compartment Door Bumper is designed from the original part for superior fitment and function. This bumper mounts within the luggage compartment to act as a Stop for the luggage compartment door closure.
Convertible Top Rest Block
p/n: 60-0415-67
Bumper, folding top rear bow (in top compartment). Two (2) required per car. Brass core as original.
Convertible Top Water Deflectors
p/n: 20-0253-67
This Convertible Top Water Deflector pair is designed from the original part for superior fitment and seal. This deflector mounts at the end of the rear roof rail for folding tops.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Roof Rail Filler
p/n: 50-0255-67
Filler, folding top side roof rail to front roof rail. Right and left with metal core as original.
Convertible Top Arm Pad
p/n: 50-0310-67
Pad, folding post, lower, on bottom of post, held by two (2) screws. Brass core, right and left hand.
Detachable Center Post Pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.
Landau Bar Spacer
p/n: 70-0351-67
Spacer, Landau bar, lower, for Landau jobs with cobra tops. Pattern on rubber matches cobra.
Convertible Top Arm Pad
p/n: 70-1216-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Convertible Top Rest Block
p/n: 60-0698-67
Pad, convertible top rest. Fully molded with metal core replacement.
Convertible Soft Top Folding Post Pads
p/n: 60-0455-67
This Convertible Soft Top Folding Post Pad pair is designed from the original part for an authentic fit, finish, and appearance. Parts fasten on the lower end with two (2) screws. Pads have a metal core.
Convertible Post Bumper
p/n: 50-0208-67
Bumper, on folding top female hinge, for folding post, when top is retracted, right and left, brass core as original.
Detachable Center Post Pad
p/n: 70-0279-67
Pads, for bottom of folding post or body, brass core as original, screw held.Length: 1.875 inches. Width: 1.0625 inches.
Convertible Quarter Window Filler
p/n: 70-2269-67
This convertible top Quarter Window Filler is designed from the original part for superior fitment and sealing. A hard to see part found at the bottom rear of the side window when the window is rolled up.
Package Tray Panel to Quarter Panel Seals
p/n: 70-4210-85
This Package Tray Panel to Quarter Panel Seal pair is designed from the original part for superior fitment and seal. This left (LH) and right (RH) seal pair fits between vehicle body quarter panel and rear package tray. This part is for the Convertible model only.
Door Filler Caps
p/n: 70-4637-70
This convertible model Door Filler Cap pair is designed from the original part for an authentic fit, finish, and function. These door fillers cap the top of the half-post between the front and rear doors on convertible models.
Convertible Top Arm Pad
p/n: 30-0441-67
Pad, convertible top to lock pillar. Molded left and right hand with metal core just like original.
Roof Rail Filler
p/n: 70-0396-67
Fillers, side roof rail to front roof rail at front corner, right and left. Metal core, threaded for original screws.
Convertible Top Arm Pad
p/n: 30-0065-67
Pads, folding top swinging arms, right and left, dovetail cross section.
Rear Quarter Window Filler
p/n: 70-3505-67
This Rear Quarter Window Filler pair is designed from the original part for superior fitment and seal. This is the rear quarter window folding top cover retainer guide with strip. Fully molded with a brass metal core and includes hardware.