Door Bumper
p/n: 30-0350-71
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Door Bumper
p/n: 17-0039-71
Bumper, round door side. An auxiliary door side bumper on door jamb pad.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1563-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure.
Door Bumper
p/n: 60-0032-71
Pad, door jamb. One (1) per door.Length: 1.25 inches. Width: .75 inches. Height: .875 inches.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 17-0041-70
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Door Bumper
p/n: 33-0505-71
This upper / lower Door Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function. Length: 7/8 inches. Width: 13/16 inches. Height: 1-1/8.
Door Bumper
p/n: 33-1234-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 30-0064-71
This fully molded slotted type Door Bumper is quality reproduction of the original factory part. Used two (2) per golf door and four (4) to eight (8) per car on open model doors.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
Door Bumper - Bottom
p/n: 70-2616-71
This Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the lower vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper - Lower
p/n: 70-1605-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rear of door lower bumper attaches to the vehicle body to support / cushion the door closure.
Door Bumper - Lower
p/n: 70-3308-71
This Lower Door Bumper is designed from the original part for superior fitment and function. Bumper pushes into slot on door at bottom.
Door Bumper Pad
p/n: 30-0032-71
This circular shaped Door Bumper Pad is designed from the original part for an authentic fit, finish, and appearance.
Door Bumper Set
p/n: 20-2365-71
Set, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Door Garnish Molding Pad
p/n: 30-0435-71
Support, door garnish molding. Up to twenty (20) required per car.Width: .875 inches. Height: 1.0 inches.
Door Hinge Bumper Set
p/n: 70-4871-71
This Door Hinge Bumper Set is a quality reproduction of the original factory part. These sixteen (16) rubber bumpers attach four (4) per door to cushion the door closure action.
Door Jamb Bumper
p/n: 20-2109-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door Jamb Bumper Pad
p/n: 40-0042-70
This Door Jamb Bumper Pad is designed from the original part for superior fitment and seal. A reproduction of earlier type, screw retained and a perfect copy.
Door Lock Bumper
p/n: 70-0538-71
Bumper, door lock striker plate. Rubber with steel core, seven sixteenths (7/16) inch thick, one (1) per door. Installed in rotary latch receiver.
Door Lock Bumper
p/n: 34-0484-71
This Door Lock Bumper is made from high-quality EPDM dense rubber to provide excellent durability. Designed for applications such as the upper door lock post.
Front of Door Bumper
p/n: 70-2614-71
This Front of Door Bumper is a quality reproduction of the original factory part. This rubber door bumper attaches to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.
Glass up stop bumper
p/n: 70-3623-62
Front door glass up stop bumper. For models w/out power vent windows. Use two (2) or four (4) per vehicle. Refer to your vehicle to see how many are required.
Lower Door and Fuel Tank Door Bumpers
p/n: 20-0004-71
Manufactured to OEM specifications this Lower Door and Fuel Tank Door Bumper pair installs for an authentic fit, finish and function. Five eighths (5/8") inches high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
Rear Door Bumpers
p/n: 70-2365-71
This Rear Door Bumper pair is made from high-quality EPDM dense rubber to provide excellent durability. Fits at the rear door opening. Proper configuration with slots for retaining screws as original.
Rear Door Bumpers
p/n: 60-0334-71
A Rear Door Bumper pair for the door check link above door. Dovetail base fits check arm.
Rear Hatch Door Bumpers
p/n: 70-4731-87
This Rear Hatch Door Bumper pair is a quality reproduction of the original factory part. These adjustable rubber bumpers attach to the rear hatch door to prevent the hatch lid from vibrating.
Rear Hatch Door Bumpers
p/n: 70-4730-87
This Rear Hatch Door Bumper pair is a quality reproduction of the original factory part. These adjustable rubber bumpers attach to the rear hatch door to prevent the hatch lid from vibrating.
Rear of Door Bumper
p/n: 70-2613-71
This Rear of Door Bumper is a quality reproduction of the original factory part. This rubber door bumper attaches to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.