Door Bumper
p/n: 60-0581-71
Pad, door jamb. (Door side bumper). Two screw type with metal reinforcing inserts.
Door Bumper
p/n: 30-0429-71
Bumper, rear door. Two (2) used per car. Correct design with proper clearance for screw hole.Width: 1.0 inches. Height: 1.0 inches.
Bumper - LH Back Door
p/n: 60-0333-71
A molded rubber Left-Hand Back Door Bumper. Dovetail to be used with old castings.
Door Bumper
p/n: 34-0342-71
Door bumper, round, rubber with steel insert, (called door anti-rattle). Two (2) per door on all closed body styles, one (1) per door on convertible Sedan.
Rear Door Bumpers
p/n: 70-2365-71
This Rear Door Bumper pair is made from high-quality EPDM dense rubber to provide excellent durability. Fits at the rear door opening. Proper configuration with slots for retaining screws as original.
Door Bumper
p/n: 40-0316-70
Bumper, door side, lower, on lock post. Retained by dovetail tapping plate.Length: 1.5625 inches. Width: 1.5625 inches.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Door Bumper Set
p/n: 20-2365-71
Set, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Door Bumper
p/n: 17-0040-71
Bumper, oblong, door side. An auxiliary door jamb or side bumper.Width: 1.75 inches. Height: .75 inches.
Door Bumper
p/n: 30-0052-71
Bumper, door side, upper. Oblong type, perfect copy of original.Length: 2.4375 inches.
Door Bumper
p/n: 17-0039-71
Bumper, round door side. An auxiliary door side bumper on door jamb pad.
Door Bumper
p/n: 30-0128-71
Pad, door jamb (Atwood type), one and five eighths (1-5/8) inch long.Width: 1.5625 inches. Height: 1.375 inches.
Door Bumper
p/n: 33-0449-71
Bumper, door, lower, held by one (1) screw and one (1) carrot retainer. Length: 1-1/8 inches. Width: 5/8 inches.
Door Bumper
p/n: 40-0131-70
Bumper, door side. Approximate size one half (1/2) inch by three fourth (3/4) inch by two (2) inch. Length: 2.0 inches. Width: .50 inches.
Door Bumper
p/n: 30-0152-71
Bumper, door, rubber, round style, screw retained. One and five sixteenths (1-5/16) inch diameter.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Door Bumper
p/n: 17-0038-70
Wedge cushion, door dovetail. This is the rubber block which goes behind the dovetail receiving bumper or shoe.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
Door Bumper
p/n: 17-0041-70
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Door Lock Bumper
p/n: 70-0538-71
Bumper, door lock striker plate. Rubber with steel core, seven sixteenths (7/16) inch thick, one (1) per door. Installed in rotary latch receiver.
Rear Door Bumpers
p/n: 60-0334-71
A Rear Door Bumper pair for the door check link above door. Dovetail base fits check arm.
Door Bumper
p/n: 10-0011-70
Cushion, door wedge plate, right and left, for door aligning lug receiver.Width: 1.1875 inches. Height: .625 inches.
Door Hinge Bumper Set
p/n: 70-4871-71
This Door Hinge Bumper Set is a quality reproduction of the original factory part. These sixteen (16) rubber bumpers attach four (4) per door to cushion the door closure action.
Door Bumper
p/n: 34-0469-71
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Door Bumper
p/n: 40-0262-70
Bumper, door.Chrysler 1934 Bumper, door. Chrysler 1932-34 Bumper, decklid. Two (2) required per car. Length: 2.50 inches. Width: 1.8125 inches.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Door Bumper
p/n: 60-0603-71
Pad, door jamb edge. With metal insert as original.Length: 1.1875 inches. Width: 1.5625 inches.