Door Bumper
p/n: 70-5023-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 70-2725-71
Bumper, door, upper rear corner attaches to the door. Two (2) needed per car.
Door Bumper
p/n: 33-1234-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1233-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1232-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1235-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
1/4" Standard Bumper
p/n: 33-0496-71
This Standard Bumper is fully molded and designed from the original part for correct fitment and seal. Designed for applications such as door opening at upper corner, license plate, and fuel filler door. Self-retaining type bumper.
1/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
Door Bumper - Lower
p/n: 70-3308-71
This Lower Door Bumper is designed from the original part for superior fitment and function. Bumper pushes into slot on door at bottom.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 70-2608-71
This Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.
Door Bumper
p/n: 70-1563-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure.
Front of Door Bumper
p/n: 70-2614-71
This Front of Door Bumper is a quality reproduction of the original factory part. This rubber door bumper attaches to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.
Door Bumper
p/n: 70-2615-71
This fully molded 5/8" Door Bumper is quality reproduction of the original factory part. This twin retainer style rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Lock Bumper
p/n: 34-0484-71
This Door Lock Bumper is made from high-quality EPDM dense rubber to provide excellent durability. Designed for applications such as the upper door lock post.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
Door Jamb Bumper
p/n: 20-2109-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
5/16" Door Bumper
p/n: 33-0293-71
Bumper, front door pillar, upper and lower. Replaces factory #3720168.
Door Bumper
p/n: 70-2877-71
Bumper, door. Requires two (2) per door - one (1) upper on door and one (1) lower on door.
Door Bumper - Lower
p/n: 70-1605-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rear of door lower bumper attaches to the vehicle body to support / cushion the door closure.
Rear of Door Bumper
p/n: 70-2613-71
This Rear of Door Bumper is a quality reproduction of the original factory part. This rubber door bumper attaches to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.
Door Garnish Molding Pad
p/n: 30-0435-71
Support, door garnish molding. Up to twenty (20) required per car.Width: .875 inches. Height: 1.0 inches.
Door Bumper
p/n: 70-2611-71
This Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.
Door Bumper - Bottom
p/n: 70-2616-71
This Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the lower vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1-3/4" Rear Door Bumper
p/n: 35-1030-71
Bumper, rear door. Plug style. Compare with your original, use as required.
Glass up stop bumper
p/n: 70-3623-62
Front door glass up stop bumper. For models w/out power vent windows. Use two (2) or four (4) per vehicle. Refer to your vehicle to see how many are required.
Door Bumper
p/n: 33-0505-71
This upper / lower Door Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function. Length: 7/8 inches. Width: 13/16 inches. Height: 1-1/8.
Door Bumper
p/n: 33-0503-71
This fully molded 3/4” Door Bumper is quality reproduction of the original factory part. Not a generic substitute but manufactured just like the factory original.
Door Bumper
p/n: 30-0312-71
Pad, door jamb. Usually requires two (2) per door.Length: 1.0 inches. Width: 1.0 inches. Height: .50 inches.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Lower Door and Fuel Tank Door Bumpers
p/n: 20-0004-71
Manufactured to OEM specifications this Lower Door and Fuel Tank Door Bumper pair installs for an authentic fit, finish and function. Five eighths (5/8") inches high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
Door Bumper
p/n: 60-0032-71
Pad, door jamb. One (1) per door.Length: 1.25 inches. Width: .75 inches. Height: .875 inches.
Door Alignment Pad
p/n: 60-0060-71
Wedge pad, door aligning dovetail. Goes under bumper retainer.Length: .9375 inches. Width: .9375 inches. Height: .4375 inches.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
Door Bumper
p/n: 30-0064-71
This fully molded slotted type Door Bumper is quality reproduction of the original factory part. Used two (2) per golf door and four (4) to eight (8) per car on open model doors.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 60-0048-71
Bumper, door side. Five eighths (5/8) inch by seven eighths (7/8) inch by one and seven sixteenths (1-7/16) inch. Two (2) door.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Door Jamb Bumper Pad
p/n: 40-0042-70
This Door Jamb Bumper Pad is designed from the original part for superior fitment and seal. A reproduction of earlier type, screw retained and a perfect copy.
Bumpers - Filler Door/Lower Door/Rear License Plate Support
p/n: 20-1302-41
A rubber Bumper pair designed from the original part for superior fitment, finish and function. Fits to the lower door and / or the fuel filler cover and / or the license plate support. Type with threaded end.
Door Bumper
p/n: 20-0003-71
Bumpers, door. Seven sixteenths (7/16) inch high. Fits on door jamb where rear of door closes against body and on rear lower part of door.
Rear Hatch Door Bumpers
p/n: 70-4730-87
This Rear Hatch Door Bumper pair is a quality reproduction of the original factory part. These adjustable rubber bumpers attach to the rear hatch door to prevent the hatch lid from vibrating.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Door Bumper
p/n: 30-0350-71
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Door Bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Door Bumper
p/n: 70-2292-70
Steele Rubber Products has the best quality door bumpers for your Street Rod or Custom Build project. Excellent for use in many applications.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Door Bumper Pad
p/n: 30-0032-71
This circular shaped Door Bumper Pad is designed from the original part for an authentic fit, finish, and appearance.
Rear Hatch Door Bumpers
p/n: 70-4731-87
This Rear Hatch Door Bumper pair is a quality reproduction of the original factory part. These adjustable rubber bumpers attach to the rear hatch door to prevent the hatch lid from vibrating.
Door Bumper
p/n: 10-0126-71
Pad, door jamb. One (1) required per door. Made to fit old door pad core.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Bumper
p/n: 60-0581-71
Pad, door jamb. (Door side bumper). Two screw type with metal reinforcing inserts.
Door Bumper
p/n: 30-0429-71
Bumper, rear door. Two (2) used per car. Correct design with proper clearance for screw hole.Width: 1.0 inches. Height: 1.0 inches.
Bumper - LH Back Door
p/n: 60-0333-71
A molded rubber Left-Hand Back Door Bumper. Dovetail to be used with old castings.
Door Bumper
p/n: 34-0342-71
Door bumper, round, rubber with steel insert, (called door anti-rattle). Two (2) per door on all closed body styles, one (1) per door on convertible Sedan.
Rear Door Bumpers
p/n: 70-2365-71
This Rear Door Bumper pair is made from high-quality EPDM dense rubber to provide excellent durability. Fits at the rear door opening. Proper configuration with slots for retaining screws as original.
Door Bumper
p/n: 40-0316-70
Bumper, door side, lower, on lock post. Retained by dovetail tapping plate.Length: 1.5625 inches. Width: 1.5625 inches.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Door Bumper Set
p/n: 20-2365-71
Set, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Door Bumper
p/n: 17-0040-71
Bumper, oblong, door side. An auxiliary door jamb or side bumper.Width: 1.75 inches. Height: .75 inches.
Door Bumper
p/n: 30-0052-71
Bumper, door side, upper. Oblong type, perfect copy of original.Length: 2.4375 inches.
Door Bumper
p/n: 17-0039-71
Bumper, round door side. An auxiliary door side bumper on door jamb pad.
Door Bumper
p/n: 30-0128-71
Pad, door jamb (Atwood type), one and five eighths (1-5/8) inch long.Width: 1.5625 inches. Height: 1.375 inches.
Door Bumper
p/n: 33-0449-71
Bumper, door, lower, held by one (1) screw and one (1) carrot retainer. Length: 1-1/8 inches. Width: 5/8 inches.
Door Bumper
p/n: 40-0131-70
Bumper, door side. Approximate size one half (1/2) inch by three fourth (3/4) inch by two (2) inch. Length: 2.0 inches. Width: .50 inches.
Door Bumper
p/n: 30-0152-71
Bumper, door, rubber, round style, screw retained. One and five sixteenths (1-5/16) inch diameter.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Door Bumper
p/n: 17-0038-70
Wedge cushion, door dovetail. This is the rubber block which goes behind the dovetail receiving bumper or shoe.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
