Taillight Mounting Pad
p/n: 27-0062-15
Pad, taillight to body mounting. Right and left molded as original with proper bead lip. Length: 4.50 inches.
Taillight to Body Weatherstrips
p/n: 70-0701-15
This Taillight To Body Weatherstrip pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body. Twenty-three and three fourths (23-3/4) inches developed length.
Taillight Mounting Pad
p/n: 50-0101-15
Right and left taillight mount pad. Replaces #1304392-3, excellent job, fully detailed.
Taillight Mounting Pad
p/n: 50-0078-15
Taillight mounting pad. Excellent copy with proper lip at edge. Replaces #1273863. Customer must cut holes for wires, bulb, screws etc as required.
Taillight Housing to Body Gasket
p/n: 20-2665-15
This Taillight to Body Gasket is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body. Thick mount type.
Taillight Lens Gasket
p/n: 70-2140-15
Gasket, trunk center medallion trunk stop lamp lens. Proper construction with accurate lips for good sealing.Length: 1.375 inches. Width: 4.0625 inches.
Taillight Gasket
p/n: 50-0355-15
Gasket, rear stop and turn signal. Four (4) piece set required per car.
Taillight Lens Gasket
p/n: 70-1213-15
Gasket, taillight lens. For the main pad order our #70-1212-15.Length: 6.875 inches.
Taillight Gasket Set
p/n: 70-2689-15
This Taillight Gasket Set is designed from the original part for superior fitment and seal. This four (4) set includes the lens gasket and welt for housing.
Taillight Gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base. Width: 3.25 inches.
Taillight Gasket
p/n: 70-2299-15
Gasket, tail light housing to body. Proper thickness sponge rubber cut to precise original configuration.
Taillight Mounting Pad
p/n: 40-0172-15
Pad, taillight bracket mounting. Right and left, plain pad without beading as original. Length: 5.3125 inches.
Taillight Mounting Pad
p/n: 40-0198-15
Pad, taillight mounting. Plain type, no bead. Length: 6.0625 inches. Width: 2.375 inches.
Taillight Mounting Pad
p/n: 40-0228-15
Mounting pad, tail and signal light. Length: 7.3125 inches. Width: 3.6875 inches.
Taillight Mounting Pad
p/n: 40-0206-15
Pad, taillight bracket to fender. This is plain style without lip. Two and five sixteenths (2-5/16) inch by five and one eighth (5-1/8) inch. Length: 5.
Taillight Lens Gasket
p/n: 70-3565-15
Gasket, taillight lens mounting gasket. Machine die cut from 1/4" thick sponge rubber. Seals tail light lens to tail light assembly. Included in our kit #70-3566-15.
Tail lamp lens gasket
p/n: 70-3569-15
Gasket, taillight lens. Fully molded rubber gasket with authentic details for left and right hand side stop lamp lens.
Taillight Lens And Housing Gaskets
p/n: 70-4053-15
This complete eight (8) piece Taillight Lens And Housing Gasket set is designed from the original part for superior fitment and seal. Includes six (6) pieces for the light lens to the taillight housing and two (2) pieces for the taillight housing to the vehicle body.
Taillight Lens Gasket
p/n: 50-0197-15
Gasket, taillight lens, one fourth (1/4) inch thick sponge rubber.
Taillight Lens Gasket
p/n: 70-1793-15
Gasket, taillight lens. Made of die cut sponge rubber to original configuration.
Taillight Lens Gasket
p/n: 25-0079-15
Gasket, taillight lens to housing. Shear die cut sponge rubber.Length: 10.0 inches.
Parking Light Gasket
p/n: 70-2023-15
Gasket, parking light housing. Die cut from durable black sponge-cell rubber. One (1) pair needed per car.Length: 11.375 inches.
Taillight Lens Gasket
p/n: 25-0100-15
Gasket set, taillight housing and lens. Eight (8) piece set used on taillight and backup light.
Tail light lens gasket
p/n: 70-3721-15
Gasket, taillight lens, two (2) piece set. Circular gasket stretches over oval shaped lens. Replaces factory #410622.
Taillight Mounting Pads
p/n: 20-2413-15
This Taillight Mounting Pad pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body.
Taillight Mounting Pad
p/n: 50-0491-15
Pad, taillight mounting. Width: 16.0 inches. Height: 9.0 inches.
Taillight Lens Gaskets
p/n: 70-3989-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens & taillight housing.
Taillight Lens Gasket
p/n: 50-0492-15
Gasket, taillight lens.Width: 14.5 inches. Height: 7.5 inches.
Taillight Mounting Pads
p/n: 20-2407-15
This Taillight Mounting Pad pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body.
Taillight Mounting Pad
p/n: 30-0290-15
Pad, taillight bracket mounting. Proper construction and beading as original.
Taillight Gasket
p/n: 70-0900-15
Gasket, taillight housing. Also order #70-0471-15 for the taillight mounting pad, and for the taillight lens gasket order #70-0658-15. Length: 8.25 inches.
Taillight Mounting Pad
p/n: 20-1794-15
Kit, taillight mounting pad. Fin and oval type. Six (6) piece set.
Taillight Mounting Pad
p/n: 20-1793-15
Kit, taillight mounting pad. Fin and Oval type. Six (6) piece set.
Taillight Mounting Pad
p/n: 20-1795-15
Kit, taillight mounting pad. Fin and oval type. Six (6) piece set.
Taillight Mounting Pad
p/n: 60-0172-15
Pad, taillight bracket mounting. Five and one half (5-1/2) inches long. Compare with our #60-0116-15. Length: 5.50 inches.
Taillight Retainer Pad
p/n: 60-0340-17
This Taillight Retainer Pad is designed from the original part for superior fitment and seal. These reproduction mounting pads fit to the rear taillight assembly.
Taillight Mounting Pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights. Length: 55.0 inches. Width: .3125 inches.
Taillight Lens Gasket
p/n: 70-0951-15
Gasket, taillight lens. Die cut one eighth (1/8) inch sponge rubber. Note: Sixty Special (60 Special) will require two (2) pairs.
Taillight Lens Gasket
p/n: 60-0147-15
Gasket, taillight lens. Two and three fourths (2-3/4) inch diameter.
Taillight Mounting Pad
p/n: 70-2583-15
Pads, taillight housing to body. Machine die cut to exact original dimensions. Constructed of high quality, long lasting sponge rubber. Replaces factory #C4GY-13420-A.
Taillight Lens Gasket
p/n: 30-0353-15
Gasket, taillight lens to body mount. High quality replacement of normally deteriorated part. Nine and one half (9-1/2) inches long.Length: 9.50 inches.
Taillight Mounting Pad
p/n: 60-0075-15
Pad, taillight and license bracket mounting. Two and five eighths (2-5/8) inch by four and one half (4-1/2) inch. Length: 4.5 inches. Width: 2.625 inches.
Taillight Mounting Pad
p/n: 70-2166-15
Pad, taillight mounting to rear quarter panel. Proper extrusion cross section like original. Two (2) strips twenty-four (24) inch long. Length: 24.0 inches.
Taillight Housing to Body Gasket
p/n: 20-2663-15
This Taillight to Body Gasket is designed from the original part for superior fitment and sealing. These thick mount type reproduction gaskets fit between taillight frame housing and the body.
Taillight to Body Gaskets - Without Reflectors
p/n: 20-1021-15
This Taillight to Body Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight frame housing and the body. For Station Wagon and Ranchero models WITHOUT reflectors.
Taillight Gasket
p/n: 60-0693-15
Seal, taillight bezel. Correct profile and long lasting material. Six (6) strips cut twelve and three fourths (12-3/4) inches long.Length: 12.75 inches.
Taillight Gasket
p/n: 60-0691-15
This Taillight Gasket is made of fully molded soft-dense rubber compound to ensure proper installation and performance. Designed from the original part for the correct profile. Two (2) strips cut thirty-six (36) inches long.
Taillight Mounting Pad
p/n: 40-0299-15
Mounting pad, taillight bracket to fender. This is a plain, flat un-beaded pad as original, and reversible. Four and three fourths (4-3/4) inch long.
Taillight Gasket
p/n: 30-0523-15
Gasket, taillight door. Two (2) strips twelve (12) inches long.Length: 12.0 inches. Width: .25 inches.
Taillight Mounting Pad
p/n: 60-0545-15
Pad, bracket mounting to body for tail and license plate light. Length: 3.3125 inches. Width: 2.5625 inches.
Turn Signal Mounting Pad
p/n: 50-0523-17
Mounting pad, turn signal bulb housing. One eighth (1/8) inch die cut sponge rubber.Width: 3.0 inches. Height: 3.75 inches.
Taillight Lens Gasket
p/n: 30-0336-15
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Taillight Lens Gasket
p/n: 70-0652-15
Gasket, taillight lens.Length: 4.75 inches. Width: 3.25 inches.
Taillight Lens Gasket
p/n: 60-0175-15
Gasket, taillight lens.Length: 3.50 inches. Width: 2.25 inches.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Taillight Lens Gaskets
p/n: 70-4049-15
This Taillight Lens Gasket pair, for right and left side, is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing.
Taillight Mounting Pad
p/n: 60-0495-15
Pad, taillight bracket to fender. Can be used for right or left hand. Two and one half (2-1/2) inch by three and five eighths (3-5/8) inch overall.
Taillight Lens and Housing Gaskets
p/n: 70-4912-15
This Taillight Lens and Housing Gasket set is designed from the original part for superior fitment and seal. Includes gaskets for Lens to Housing (2) and Housing to Body (2).
Taillight Lens Gaskets
p/n: 70-3240-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Taillight Mounting Pad
p/n: 60-0364-15
Pad, taillight mounting to rear fender. Length: 1.0625 inches.
Reflector gasket
p/n: 50-0360-15
Seal, reflector signal, between taillights. With correct slits for tabs on reflector. One (1) pair required per car.
Taillight Lens Gasket
p/n: 50-0449-15
Gasket, taillight lens. Die cut from three sixteenths (3/16) inch sponge.Width: 8.75 inches. Height: 3.875 inches.
Taillight Mounting Pad
p/n: 60-0472-15
Pad, taillight bracket mounting. Two and three sixteenths (2-3/16) inch by three and three fourths (3-3/4) inch inside of bead.
Taillight Gasket
p/n: 60-0692-15
Seal, taillight bezel. Correct profile and long lasting material. Two (2) strips cut twenty four and three fourths (24-3/4) inches long.Length: 24.
Taillight Gasket
p/n: 60-0694-15
Seal, taillight bezel. Correct profile and long lasting material. Two (2) strips cut fourteen and three fourths (14-3/4) inches long.
Wiring grommet
p/n: 70-0864-15
Grommet, taillight wiring through trunk inner panel. One (1) pair per car.
Taillight Lens And Housing Gaskets
p/n: 70-4168-15
This four (4) piece Taillight Lens And Housing Gasket set is designed from the original part for superior fitment and seal. This set does both taillights. Includes two (2) light lens to the housing gaskets and two (2) housing to vehicle body gaskets.
