1-5/8" Firewall Grommet
p/n: 50-0363-20
This Firewall Grommet is used to run the windshield washer hose through the firewall. Designed from original part for excellent workmanship.
1-11/16" Main Harness Firewall Grommet
p/n: 70-2606-20
This Firewall Grommet fits to the engine firewall where main wire harness plugs in. Designed from the original part for superior fitment and finish.
1-3/16" Firewall Grommet
p/n: 32-0394-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1-3/8" Firewall Grommet
p/n: 70-0712-20
This Firewall Grommet is designed from the original part for superior fit and seal. Made from high-quality dense rubber to provide excellent durability. Two (2) holes in grommet.
1-5/16" Firewall Grommet
p/n: 32-0347-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for wiper control cable and heat tube.
Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
1-5/8" Cowl Hole Grommet
p/n: 70-2065-20
This Firewall Grommet is used to plug the hole on the cowl side of the firewall. Designed from original part for excellent workmanship.
Firewall Grommet
p/n: 70-2600-20
This Firewall Grommet is used to prevent chaffing or wiring, hoses, or cables that pass through the firewall, door, or trunk. Designed from original part for excellent workmanship.
Overdrive Cable Grommet
p/n: 20-1812-20
This Overdrive Cable Grommet is used to help protect the overdrive pull cable when passing through the sheet metal of the firewall.
1-9/16" Firewall Grommet
p/n: 50-0566-20
This Firewall Grommet is used to used to run the water temperature gauge, heater blower wire, or other various wires through the firewall. Designed from the original part for superior fit and seal.
1-5/16" Firewall Grommet
p/n: 32-1215-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Designed for wire, cable, tubes, etc, in the firewall.
Firewall Retainer
p/n: 30-0207-20
Fastener, firewall insulation. Three fourths (3/4) inch diameter head by one (1) inch long.Height: 1.0 inches.
Main Wiring Loom Grommet
p/n: 20-2433-20
This Main Wiring Loom Grommet is used to protect the wiring from the sheet metal of the firewall. Made from high-quality dense rubber to provide excellent durability.
1-1/2" Firewall Grommet
p/n: 32-0225-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Radiator Mounting Pad
p/n: 30-0469-31
Pad (or Grommet), radiator to dash tie rod. Die cut from one fourth (1/4) inch rubber. Four (4) used per car.Height: .25 inches.
1-3/8" Firewall Grommet
p/n: 32-0333-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as ignition cable and temperature gauge.
1-5/8" Firewall Grommet
p/n: 32-0226-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the handbrake cable.
1" Firewall Access Plug
p/n: 35-1214-20
This Floor Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Designed for unused holes in firewall.
1-3/32" Firewall Grommet
p/n: 32-1201-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Typically used for wiring.
Speedometer Cable Grommet
p/n: 20-0435-41
This Speedometer Cable Grommet is generally used where the speedometer cable goes through the sheet metal of the firewall. Designed from the original part for superior fit and seal.
Firewall Plug - Oval Rubber
p/n: 20-0754-20
This Firewall Plug is designed from the original part for superior fitment and finish. Usually requires three oval plugs per truck.
Speedometer Housing Grommet
p/n: 20-0447-20
This Speedometer Housing Grommet is used where the cable runs through the floorboard. Also allows for the choke and throttle cable to go through the firewall.
1-1/16" Firewall Grommet
p/n: 25-0098-20
This Firewall Grommet is used to run the oil pressure gauge line through the firewall. Designed from original part for excellent workmanship.
1-5/16" Firewall Grommet
p/n: 50-0532-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from original part for excellent workmanship.
1-1/4" Firewall Grommet
p/n: 32-0220-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for firewall applications such as for the overdrive cable.
1-3/8" Firewall Grommet
p/n: 32-0062-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as getting the switch and coil wire through the firewall.
1-1/16" Firewall Grommet
p/n: 70-1771-20
This Firewall Grommet used to run the speedometer cable through the firewall. The grommet can also be used to run the trunk lid release cable through the rear compartment.
3/4" Firewall Plug
p/n: 35-0197-31
This Firewall Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
1-7/32" Firewall Grommet
p/n: 32-1961-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1-1/4" Firewall Grommet
p/n: 32-0422-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the speedometer cable through the firewall.
15/16" Utility Plug
p/n: 35-0099-20
This Utility Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Speedometer Cable Grommet
p/n: 20-2435-20
This Speedometer Cable Grommet is used to protect the cable when running it through the firewall. Designed from the original part for superior fit and seal.
Windshield Wiper Hose Grommet
p/n: 20-0546-20
This Windshield Wiper Hose Grommet is used as a guard to run the wiper hose through the firewall. Made from top quality rubber to ensure durability and proper fitment.
3/4" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Air Vent Cable Grommet
p/n: 20-2437-20
This Air Vent Cable Grommet is used where the air cable passes through the firewall. One pair required per vehicle. This grommet is also commonly used for the hood pull cable, heater wire, and electric wiper motor cable.
1" Wiring Grommet
p/n: 32-0439-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
11/16" Firewall Grommet
p/n: 32-0112-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as the handbrake cable, heater control cable, and others.
1-1/16" Headlight Grommet
p/n: 32-0437-20
This Headlight Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the horn and headlight wires crossover through the radiator shroud.
Firewall Retainer
p/n: 60-0586-20
This Firewall Retainer is used on the firewall insulation panel. Designed from original for the "Christmas Tree" style popular during this time.
7/8" Wiring Grommet
p/n: 32-0002-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Windshield Wiper Hose Grommet
p/n: 20-2300-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from the original part for superior fit and seal.
Windshield Wiper Hose Grommet
p/n: 20-1611-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from original part so it fits correctly.
11/16" Wiring Grommet
p/n: 32-0003-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1" Firewall Grommet
p/n: 32-0513-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the heater vent control cable through the firewall.
1/2" Firewall Grommet
p/n: 32-0365-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for firewall applications such as the vent control cable.
3/4" Firewall Grommet
p/n: 32-0263-17
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as license lamp wire through the body, parking brake front cable, and idler lever pull rod.
3/4" Firewall Grommet
p/n: 32-0162-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for firewall applications such as ignition to starter wire through the firewall.
Choke and Throttle Dash Grommets
p/n: 20-0347-41
This Choke and Throttle Dash Grommet pair mounts in the dash where the choke and throttle rods pass through the dash to keep rods from rattling.