Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Bumper Cap - Door, Hood and Trunk
p/n: 82-0020-42
This Bumper Cap is a quality reproduction of the original factory part. Serves as a Door, Hood and Trunk Bumper Cap for adjustment bolt. 7/8" diameter X 7/16" thick. Each
Fender Bumper
p/n: 33-0441-44
Bumper, between grill and fender. One fourth (1/4) inch thickness, five sixteenths (5/16) inch sheet metal holes.
Fender To Hood Side Cushion Bumper
p/n: 70-2610-42
This Fender To Hood Side Cushion Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Firewall To Hood Bumpers
p/n: 20-2758-42
These Firewall To Hood Bumpers are a quality reproduction of the original factory part. Includes attaching screws. Three (3) piece set.
Firewall to Hood Weatherstrip
p/n: 20-2749-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body. Includes attaching clips pre-installed.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-0790-42
This Firewall to Hood Weatherstrip - Cowl Lacing is made of high-quality EPDM dense rubber and to the original design for a factory like fit and appearance. Comes with mounting clips installed.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 20-0681-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This Cowl Lacing weatherstrip installs at the rear of the engine bay to seal between the closing hood and the vehicle firewall.
Folding Seat Bumper
p/n: 34-0004-88
Bumper, folding seat rest. Also used as hood pad. Original configuration, with fabric base and molding screw hole to fit #10-32 screw.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Front Hood Corner Pads
p/n: 14-0035-42
This Front Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Front Inner Fender to Hood Weatherstrip
p/n: 82-0159-45
A Front Inner Fender To Hood Weatherstrip made with the proper cross section of rubber like the original for durability and a like factory seal. Fits over the inner fender panel and seals to hood assembly. Sold individually, two (2) per vehicle required.
Hood and Fender Bumper
p/n: 70-3446-42
This Hood / Fender Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the front fender to support / cushion the hood closure.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Bumper
p/n: 25-0086-42
Bumper, hood-to-fender. Requires six (6) per car.Length: 1.375 inches. Width: .875 inches.
Hood bumper
p/n: 70-3377-42
Bumper, hood-to-fender. Slides into slot on fender flange. Four (4) required per car.
Hood bumper
p/n: 20-0041-42
Bumpers, rear of hood to top of fender. Two (2) required per vehicle.Ford Cars 1961-64 Bumpers, rear of hood to top of fender. Requires 2 pair for hood.
Hood bumper
p/n: 20-1309-42
Bumper, hood pull cam. Two (2) required per car.Ford Cars 1957-60 Bumper, hood pull cam. 2 required per car. Ford Cars 1958-59 Bumper, trunk lid.
Hood Bumper
p/n: 40-0313-42
Bumper, hood panel assembly. Same as our #40-0164-42. (except vulcanized to brass cores). Length: 1.375 inches. Width: 1.3375 inches.