Hood Bumper
p/n: 70-2020-42
Bumper, hood ledge. Original type retainer and proper factory type profile.Width: .75 inches. Height: 1.25 inches.
Hood Side Upper Bumper
p/n: 70-2617-42
This Hood Side Upper Bumper is fully molded with top quality EPDM rubber. The authentic configuration for 1/4" hole. Six (6) bumpers typically required per vehicle.
Hood, Door Or Liftgate Bumpers
p/n: 20-0907-71
This Hood, Door Or Liftgate Bumper pair is a quality reproduction of the original factory part.
Hood bumper
p/n: 70-2876-42
Bumper, hood adjustable, rear. Slip-over rubber cover for threaded stud that mounts on both sides of cowl.
Fender To Hood Side Cushion Bumper
p/n: 70-2610-42
This Fender To Hood Side Cushion Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Hood Bumper
p/n: 60-0034-42
Bumper stop, hood, lower center. Two (2) required per vehicle.Length: 1.0 inches. Width: .75 inches. Height: .4375 inches.
Hood To Fender Bumper
p/n: 50-0473-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.
Hood To Fender Bumpers
p/n: 70-4734-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fenders to support / cushion the hood closure.
Hood To Fender Bumpers
p/n: 70-4735-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fenders to support / cushion the hood closure.
Hood Bumper
p/n: 27-0103-42
Bumper, hood to fender ledge. Uses four (4) per car.Width: 1.25 inches. Height: .9375 inches.
Fender Bumper
p/n: 33-0441-44
Bumper, between grill and fender. One fourth (1/4) inch thickness, five sixteenths (5/16) inch sheet metal holes.
Hood Bumper
p/n: 50-0325-42
Bumper, hood front. Slides over metal bracket.1941 model requires two (2) per car. 1942 model requires two to four (2-4) per car.Length: 1.0 inches.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Firewall To Hood Bumpers
p/n: 20-2758-42
These Firewall To Hood Bumpers are a quality reproduction of the original factory part. Includes attaching screws. Three (3) piece set.
Adjustable Hood Bumper
p/n: 70-0973-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. 1957-1958 models use four (4) per vehicle. 1959-1960 models use two (2) per vehicle.
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
Hood Bumper
p/n: 50-0490-42
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
Hood bumper
p/n: 70-2871-42
Bumper, hood, front adjustable. Bumper threads into radiator support on left and right side. Two (2) required per car.
Adjustable Hood Bumper
p/n: 70-0935-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Hood to Fender Bumper Set
p/n: 20-1312-42
This four (4) piece Hood to Fender Bumper Set is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 25-0089-42
Bumper, hood to fender. Four (4) to six (6) per car.Length: 1.5625 inches. Width: .875 inches.
Hood Bumper
p/n: 70-1543-42
Bumper, hood adjustable. Fully molded rubber, two (2) required per car. Does not include bolt.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Hood to Fender Bumper
p/n: 70-2756-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 50-0489-42
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
Hood Bumper
p/n: 25-0086-42
Bumper, hood-to-fender. Requires six (6) per car.Length: 1.375 inches. Width: .875 inches.
Radiator Grille Pads
p/n: 20-1575-31
This four (4) piece Radiator Grille Pad set is designed from the original part for an authentic fit, finish, and appearance.
Hood To Fender Bumper Set
p/n: 70-2872-42
These Hood to Fender Bumper are a quality reproduction of the original factory part. The rubber bumper attaches to the front fender to support / cushion the hood closure. Four (4) piece set for two (2) bumpers per side.
Hood to Fender Bumper Set
p/n: 70-2672-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 70-0987-42
Bumper assembly, with stud. Two (2) or four (4) used per car as required.Height: 3.25 inches.
Adjustable Hood Bumper
p/n: 70-2830-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires three (3) per vehicle.
Firewall to Hood Weatherstrip
p/n: 20-2749-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body. Includes attaching clips pre-installed.
Hood Bumper
p/n: 20-0211-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Hood To Fender Bumper
p/n: 60-0318-42
This Hood To Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle, order as needed.
Hood Bumper
p/n: 20-0209-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Hood Bumper
p/n: 34-0311-42
Bumper, hood, fastened to cowl at rear of hood. Steel core. One and eleven sixteenths (1-11/16) inch diameter. Two (2) per car.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 27-0098-42
Bumper, hood front to radiator ledge, adjustable. Includes plated bolt and rubber cushion.Length: 2.1875 inches.
Hood Bumper
p/n: 50-0277-42
Bumper, hood side to fender ledge. Metal core molded in as original.Width: 1.875 inches. Height: .8125 inches.
Hood to Fender Bumper
p/n: 25-0091-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Hood to Fender Bumper
p/n: 25-0068-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 25-0076-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Hood To Fender Bumper Set
p/n: 20-1313-42
This four (4) piece Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attaches to the front fender to support / cushion the hood closure.
Hood bumper
p/n: 20-0041-42
Bumpers, rear of hood to top of fender. Two (2) required per vehicle.Ford Cars 1961-64 Bumpers, rear of hood to top of fender. Requires 2 pair for hood.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Hood to Fender Bumper
p/n: 70-2043-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 27-0056-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Corner Pad
p/n: 60-0006-42
Pad, hood, rear corner. Brass core and tabs, excellent copy. In 1935: Two (2) are used per car. In 1936: Four (4) are used per car.
Hood to Fender Bumper
p/n: 70-3445-42
Bumpers, hood to fender. Set of four (4). Proper cross section with original details approximately five eights (5/8") of an inch wide.
Hood to Fender Bumper
p/n: 60-0675-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. Four (4) piece set. Exact profile for 1964, not universal or '63 type.
Hood to Fender Bumper Set
p/n: 60-0696-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Correct cross-section. Four (4) piece set.
Hood Bumper
p/n: 20-0207-42
Bumper, hood on fender. Push-in type. Three fourths (3/4) inch wide. Four (4) piece set.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Hood rest pad
p/n: 70-0139-42
Pad, hood rest (hood bumper). In years 1941-47 purchase six (6) per car. In year 1948-1949 purchase two (2) per car.
Folding Seat Bumper
p/n: 34-0004-88
Bumper, folding seat rest. Also used as hood pad. Original configuration, with fabric base and molding screw hole to fit #10-32 screw.