Hood Bumper Set
p/n: 20-3004-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood to Fender Bumper Set
p/n: 70-2315-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper Set
p/n: 20-0078-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Bumper
p/n: 30-0150-42
Bumpers, hood rest, reversible.Length: 2.1875 inches. Width: 1.5625 inches.
Hood Bumper
p/n: 30-0080-42
Bumper, inner hood rest. Good copy and material. One (1) pair required per car.Length: 1.50 inches. Width: .875 inches.
Hood bumper
p/n: 70-0543-42
Bumpers, hood to fender. Mounted on hood, rubber with steel core. Replaces Bakelite originals which are not available.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Hood Bumper Set
p/n: 20-0212-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Bumper Set
p/n: 20-0210-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Hood Bumper Set
p/n: 20-0208-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Corner Pad Set
p/n: 20-2017-42
This twenty-six (26) piece Hood Corner Pad set is designed from the original parts for superior fitment and function. The set includes grille area and cowl bumpers as required.
Hood Bumper Set
p/n: 20-2187-42
This twenty-two (22) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Hood Inner Center Rest Pad
p/n: 30-0222-42
This Hood Inner Center Rest Pad pair is designed from the original part for an authentic fit, finish, and appearance. Rubber only pads that fit original bracket.
Hood Bumper Set
p/n: 20-2185-42
This twenty (20) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Corner Pad
p/n: 60-0118-42
Pad. hood corner, steel core as original, front and rear.Length: 1.5 inches.
Hood Corner Pad Set
p/n: 20-2015-42
This fourteen (14) piece Hood Corner Pad set is designed from the original parts for superior fitment and function. Includes grille area and cowl bumpers as required.
Hood Corner Pad Set
p/n: 20-2018-42
This twelve (12) piece Hood Corner Pad set is designed from the original parts for superior fitment and function. The set includes grille area and cowl bumpers as required.
Hood Corner Pad
p/n: 70-0914-42
Pad, hood corner. Molded left and right like original.Width: 1.375 inches.
Hood Bumper Set
p/n: 20-0356-42
This comprehensive Hood Bumper set is designed from the original part for superior fitment and function. The sixteen (16) piece set includes four (4) grille area bumpers and four (4) cowl bumpers with eight (8) rivets.
Hood Corner Pads
p/n: 40-0187-42
This Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Hood Bumper
p/n: 40-0164-42
Pad, hood panel center bracket. Hollow, to fit over original steel bracket.Length: 1.375 inches. Width: 1.375 inches.
Hood Bumper
p/n: 30-0151-42
Bumpers, hood catch. Right and left.Length: 2.50 inches. Width: 1.4375 inches.
Hood Corner Pad
p/n: 27-0031-42
Pads, hood front corners, right and left. Metal core as original with integral mounting tabs for hole in hood corner.Width: 1.875 inches. Height: .
Hood Corner Pad
p/n: 40-0090-42
Pads, hood rear corners. Open angle for long hood. Metal core as original.Length: 1.50 inches.
Hood Corner Pad
p/n: 30-0037-42
Pads, hood front corner. Metal core, retained by single rivet.Length: 1.75 inches. Width: 1.375 inches.
Hood fastener seal plate
p/n: 50-0225-42
Seal plate, hood fastener control, cable through firewall. Rubber with brass core.
Hood Side Bumpers
p/n: 20-0791-42
A four (4) piece Hood Side Bumper set that is manufactured to OEM specifications to install for an authentic fit, finish, and function. Reproduction bumpers designed from the original part.
Hood Front Corner Pads
p/n: 60-0052-42
Left and Right Front Hood Corner Pad pair designed from the original part for superior fitment, finish and function. Has metal core as original, with metal tabs for securing pad to hood.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Corner Pads
p/n: 27-0032-42
This left and right rear Hood Corner Pad pair is designed from the original part for an authentic fit, finish, and appearance. Metal core as original with integral mounting tabs for hole in hood corner.
Hood Corner Pad
p/n: 70-0047-42
Pads, hood corners, rear. Original style with metal core and metal fastening tabs.
Hood Corner Pad
p/n: 50-0036-42
Pads, hood corners, front. Original type with metal core and retaining tab.Width: 1.625 inches.
3" Firewall Grommet
p/n: 30-0110-42
This Firewall Grommet pair is used for the hood lock link through the firewall. Designed from the original part for superior fit and seal.
Hood Louver Corner Stop
p/n: 33-0129-42
Corner stop, hood louver, self-holding, original size and profile, fits one fourth (1/4) inch hole in sheet metal.
Hood bumper
p/n: 50-0326-42
Bumper, hood side pilot. Four (4) piece set required per car. Steel washer vulcanized inside rubber.
Hood Corner Pad
p/n: 25-0030-42
Pads, rear hood corners, right and left. Brass core as original, with steel self-held tabs.Length: 1.75 inches. Width: 1.1875 inches.
Hood Corner Pad
p/n: 25-0029-42
Pads, front hood corners, right and left. Brass core as original, with self-held steel tabs.Length: 1.75 inches. Width: 1.3125 inches.
Hood to Cowl Weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Hood Corner Pad
p/n: 30-0225-42
Pads, front and rear hood corners, brass core, right angle.Length: 2.625 inches. Width: 2.625 inches.
Hood Rear Corner Pads
p/n: 60-0053-42
Left and Right Front Hood Corner Pad pair designed from the original part for superior fitment, finish and function. Has metal core as original, with metal tabs for securing pad to hood.
Hood Corner Pad
p/n: 40-0089-42
Pads, hood front corners. Rubber with metal core as original.Length: 1.4375 inches.
Hood Corner Pad
p/n: 60-0399-42
Bumpers, hood front corners. Right and Left with metal cores.Width: 1.625 inches.
Hood to Fender Weatherstrips
p/n: 70-1016-42
This Hood To Fender Weatherstrip pair is an exact profile dense rubber extrusion. The weatherstrip pair fits between the front fenders and hood. Two (2) strips at sixteen (16") inches long.
Hood Corner Pad
p/n: 50-0452-42
Pad, hood corners, rear. Molded left and right with metal core.Width: 1.625 inches. Height: 1.375 inches.
Hood Corner Pad
p/n: 50-0290-42
Pads, hood corners, rear, right and left, metal cores.Width: 1.5 inches. Height: 1.25 inches.
Hood Corner Pad
p/n: 60-0042-42
Pads, hood corners, right and left. Four (4) piece set.Width: 1.125 inches. Height: 1.125 inches.
Hood Vent Bumper
p/n: 33-0053-42
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Hood Corner Pad
p/n: 25-0052-42
Pad, hood corner front or rear. Made with metal core.Length: 2.25 inches. Width: 1.5 inches.
Hood Corner Pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Hood Corner Pad
p/n: 30-0088-42
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Hood Corner Pad
p/n: 30-0183-42
Pads, hood corners. Right and left replacement. Brass core, integral holding tabs.Length: 3.125 inches.
Hood ventilator wedge pad
p/n: 70-0317-42
Wedge pads, hood side ventilators. Fourteen (14) piece set.
Hood Ventilator Bumper Set
p/n: 70-0011-42
This forty (40) piece Hood Ventilator Bumper set is designed from the original parts for superior fitment and function. The set includes bumpers and rivets for one (1) hood.
Hood Bumper
p/n: 40-0313-42
Bumper, hood panel assembly. Same as our #40-0164-42. (except vulcanized to brass cores). Length: 1.375 inches. Width: 1.3375 inches.
Hood Corner Pad
p/n: 30-0059-42
Pad, hood rear corner. Molded left and right with a metal core. Length: 2.50 inches. Width: 1.75 inches.
Hood Corner Pad
p/n: 30-0011-42
Pads, hood front corners, large type. Molded right and left with metal cores and double tab retainers.Length: 3.1875 inches. Width: 2.125 inches.
Hood Corner Pad
p/n: 17-0035-42
Pads, hood rear corners, exact copy with metal core as original. Right and Left (reversible).Width: 2.50 inches. Height: 1.75 inches.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Hood Corner Pad
p/n: 30-0130-42
Pads, hood front corners. Large self prong type with metal core molded left and right.Length: 3.375 inches.
Hood Bumper
p/n: 40-0118-42
Bumpers, hood top panel to side panels. Four (4) piece set with brass core as original. Four (4) per vehicle.
Hood center protector
p/n: 70-0342-42
Protector, hood center. Brass core as original threaded to fit original screws.
Hood to Cowl Bumpers
p/n: 30-0223-42
Bumpers, hood to cowl. Brass core, one and one half (1-1/2) inch by four and one half (4-1/2) inch.Length: 4.50 inches. Width: 1.50 inches.
Front Hood Corner Pads
p/n: 14-0035-42
This Front Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Hood to Cowl Weatherstrip
p/n: 30-0138-42
Guard strip, hood to cowl. Brass core with molded integral hood rest.Length: 14.875 inches.
Shaker Hood Air Cleaner Seal
p/n: 20-2766-45
This Shaker Hood Air Cleaner Seal includes drain hose and correct FoMoCo script. Made from Original Ford Tooling.
Hood Corner Pad
p/n: 17-0036-42
Pads, hood front corners, exact copy with metal core as original. Right and Left.Width: 2.50 inches.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Hood to fender weatherstrip
p/n: 70-2728-42
Seal, hood to fender. Mounts on fender at hinge area inside hood opening. Fits around hood hinge assembly to isolate engine compartment from car interior. Replaces factory #E3SZ-16071-B, E3SZ-16072-B.