1/2" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
1/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
1/4" Hood Bumper
p/n: 33-0003-42
Bumper, hood, 2 uses. Hood to radiator shell at side panel, hood to fender, as required.
3" Firewall Grommet
p/n: 30-0110-42
This Firewall Grommet pair is used for the hood lock link through the firewall. Designed from the original part for superior fit and seal.
3/16" Hood Vent Bumper
p/n: 33-0042-42
Hood ventilator door bumper, stem retainer. Twelve (12) required per car.
5/16" Hood Bumper
p/n: 33-0031-42
Self-retaining hood bumper, along edge of hood against fender. Up to twenty (20) per car.
5/16" Hood Side to Fender Bumper
p/n: 33-0542-42
A quality Hood Side To Fender Bumper. Button type and self-retaining. Replaces factory #391463.
5/16” Round Top Hood Bumper
p/n: 20-2755-42
This Hood Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the front radiator support to cushion / bump stop the hood closure.
Adjustable Hood Bumper
p/n: 70-0935-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function.
Adjustable Hood Bumper
p/n: 70-2830-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires three (3) per vehicle.
Adjustable Hood Bumper
p/n: 70-0973-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. 1957-1958 models use four (4) per vehicle. 1959-1960 models use two (2) per vehicle.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Bumper Cap - Door, Hood and Trunk
p/n: 82-0020-42
This Bumper Cap is a quality reproduction of the original factory part. Serves as a Door, Hood and Trunk Bumper Cap for adjustment bolt. 7/8" diameter X 7/16" thick. Each
Fender Bumper
p/n: 33-0441-44
Bumper, between grill and fender. One fourth (1/4) inch thickness, five sixteenths (5/16) inch sheet metal holes.
Fender To Hood Side Cushion Bumper
p/n: 70-2610-42
This Fender To Hood Side Cushion Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Firewall To Hood Bumpers
p/n: 20-2758-42
These Firewall To Hood Bumpers are a quality reproduction of the original factory part. Includes attaching screws. Three (3) piece set.
Firewall to Hood Weatherstrip
p/n: 20-2749-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body. Includes attaching clips pre-installed.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-0790-42
This Firewall to Hood Weatherstrip - Cowl Lacing is made of high-quality EPDM dense rubber and to the original design for a factory like fit and appearance. Comes with mounting clips installed.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 20-0681-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This Cowl Lacing weatherstrip installs at the rear of the engine bay to seal between the closing hood and the vehicle firewall.
Folding Seat Bumper
p/n: 34-0004-88
Bumper, folding seat rest. Also used as hood pad. Original configuration, with fabric base and molding screw hole to fit #10-32 screw.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Front Hood Corner Pads
p/n: 14-0035-42
This Front Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Front Inner Fender to Hood Weatherstrip
p/n: 82-0159-45
A Front Inner Fender To Hood Weatherstrip made with the proper cross section of rubber like the original for durability and a like factory seal. Fits over the inner fender panel and seals to hood assembly. Sold individually, two (2) per vehicle required.
Hood and Fender Bumper
p/n: 70-3446-42
This Hood / Fender Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the front fender to support / cushion the hood closure.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Bumper
p/n: 25-0086-42
Bumper, hood-to-fender. Requires six (6) per car.Length: 1.375 inches. Width: .875 inches.
Hood bumper
p/n: 70-3377-42
Bumper, hood-to-fender. Slides into slot on fender flange. Four (4) required per car.
Hood bumper
p/n: 20-0041-42
Bumpers, rear of hood to top of fender. Two (2) required per vehicle.Ford Cars 1961-64 Bumpers, rear of hood to top of fender. Requires 2 pair for hood.
Hood bumper
p/n: 20-1309-42
Bumper, hood pull cam. Two (2) required per car.Ford Cars 1957-60 Bumper, hood pull cam. 2 required per car. Ford Cars 1958-59 Bumper, trunk lid.
Hood Bumper
p/n: 40-0313-42
Bumper, hood panel assembly. Same as our #40-0164-42. (except vulcanized to brass cores). Length: 1.375 inches. Width: 1.3375 inches.
Hood bumper
p/n: 50-0326-42
Bumper, hood side pilot. Four (4) piece set required per car. Steel washer vulcanized inside rubber.
Hood Bumper
p/n: 40-0118-42
Bumpers, hood top panel to side panels. Four (4) piece set with brass core as original. Four (4) per vehicle.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Hood Bumper
p/n: 50-0468-42
Bumper, hood side to fender. Six (6) required per car.Width: 1.8125 inches. Height: 1.8125 inches.
Hood Bumper
p/n: 20-0014-42
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Hood bumper
p/n: 70-2876-42
Bumper, hood adjustable, rear. Slip-over rubber cover for threaded stud that mounts on both sides of cowl.
Hood Bumper
p/n: 70-0987-42
Bumper assembly, with stud. Two (2) or four (4) used per car as required.Height: 3.25 inches.
Hood Bumper
p/n: 25-0089-42
Bumper, hood to fender. Four (4) to six (6) per car.Length: 1.5625 inches. Width: .875 inches.
Hood Bumper
p/n: 70-1543-42
Bumper, hood adjustable. Fully molded rubber, two (2) required per car. Does not include bolt.
Hood Bumper
p/n: 70-2735-42
This adjustable Hood Bumper mounts at the front of the vehicle over the radiator. 1.0 x 44mm thread with 23mm hex head.
Hood Bumper
p/n: 50-0277-42
Bumper, hood side to fender ledge. Metal core molded in as original.Width: 1.875 inches. Height: .8125 inches.
Hood Bumper
p/n: 70-0866-42
This Hood Bumper is a quality reproduction of the original factory part. The hood bumpers provide a cushion for the hood closure that also minimizes vibration.
Hood Bumper
p/n: 50-0489-42
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
Hood Bumper
p/n: 70-1607-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to support / cushion the hood closure.
Hood Bumper
p/n: 60-0034-42
Bumper stop, hood, lower center. Two (2) required per vehicle.Length: 1.0 inches. Width: .75 inches. Height: .4375 inches.
Hood Bumper
p/n: 70-2020-42
Bumper, hood ledge. Original type retainer and proper factory type profile.Width: .75 inches. Height: 1.25 inches.
Hood Bumper
p/n: 70-0991-42
Bumper, hood to fender ledge. Typically four (4) to six (6) used per car.Length: 1.15625 inches. Width: .3125 inches.
Hood Bumper
p/n: 20-2753-42
This Hood Bumper is a quality reproduction of the original factory part. The bumper attaches to the front fenders to support/cushion the hood closure. Used to provide a cushion for the hood closure that also minimizes vibration.
Hood bumper
p/n: 70-2871-42
Bumper, hood, front adjustable. Bumper threads into radiator support on left and right side. Two (2) required per car.
Hood Bumper
p/n: 50-0511-42
Bumper, hood to fender ledge. Correct detail, made from highest quality rubber.Width: .75 inches. Height: .875 inches.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Hood Bumper
p/n: 50-0325-42
Bumper, hood front. Slides over metal bracket.1941 model requires two (2) per car. 1942 model requires two to four (2-4) per car.Length: 1.0 inches.
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Hood Bumper
p/n: 82-0212-42
Bumper, hood to fender ledge. Excellent reproduction, made just like original.
Hood Bumper
p/n: 30-0150-42
Bumpers, hood rest, reversible.Length: 2.1875 inches. Width: 1.5625 inches.
Hood Bumper
p/n: 34-0311-42
Bumper, hood, fastened to cowl at rear of hood. Steel core. One and eleven sixteenths (1-11/16) inch diameter. Two (2) per car.
Hood Bumper
p/n: 20-0209-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Hood Bumper
p/n: 30-0080-42
Bumper, inner hood rest. Good copy and material. One (1) pair required per car.Length: 1.50 inches. Width: .875 inches.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Hood Bumper
p/n: 30-0151-42
Bumpers, hood catch. Right and left.Length: 2.50 inches. Width: 1.4375 inches.
Hood Bumper
p/n: 20-0207-42
Bumper, hood on fender. Push-in type. Three fourths (3/4) inch wide. Four (4) piece set.
Hood Bumper
p/n: 70-1608-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.