1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
3/16" x 5/8" Fabric Hood Lacing
p/n: 70-4768-42
This 3/16" x 5/8" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Cowl End Weatherstrips
p/n: 70-4917-43
This Cowl End Weatherstrip pair is designed from the original part for superior fitment and function. Die cut from correct sponge rubber.
Cowl Firewall Weatherstrip
p/n: 20-2021-43
This Cowl Firewall Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction with correct contours to seal out fumes and eliminate rattles.
Cowl Lacing Rubber Seal
p/n: 20-1587-42
This Cowl Lacing Rubber Seal is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body to seal between the firewall and hood.
Cowl Panel to Cowl Filler Seals
p/n: 70-3695-43
This Cowl Panel to Cowl Filler Gasket pair is designed from the original part for superior fitment and function. These seals go under the cowl vent grille on the left and right sides of it.
Fabric Hood Lacing
p/n: 20-0354-42
This Fabric Hood Lacing installs where the hood rests on the cowl panel. Original woven style lacing complete with installation tacks. Sold as a forty-nine (49) inch strip.
Firewall to Hood Cowl Lacing
p/n: 20-0352-42
A cloth Firewall to Hood Cowl Lacing measuring approximately ninety (90") inches in length and complete with mounting screws. Designed from the original part for superior fitment, finish and function.
Firewall to Hood Seal
p/n: 70-4275-43
This Firewall to Hood Seal weatherstrip is designed from the original part for superior fitment and seal. Seal installs on the top edge of the firewall where the hood meets the cowl. Push-on to body mounting with no adhesive required.
Firewall to Hood Weatherstrip
p/n: 70-4200-43
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal has the proper cowl radius to fit correctly. Mounts with ten (10) pre-installed clips at the rear of the engine bay directly to the body.
Firewall to Hood Weatherstrip
p/n: 20-2750-42
This Firewall to Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Firewall to Hood Weatherstrip
p/n: 70-3465-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile made in sponge rubber. This weatherstrip installs at the rear of the engine bay to seal between the hood and the vehicle firewall.
Firewall to Hood Weatherstrip
p/n: 20-2760-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and the vehicle firewall.
Firewall To Hood Weatherstrip
p/n: 20-2751-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay firewall directly to the body to keep water and debris out.
Firewall to Hood Weatherstrip
p/n: 70-3123-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. Installs with the pre-installed clips on the front edge of the cowl.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 20-1091-42
This Firewall To Hood Weatherstrip - Cowl Lacing mounts under the rear of the hood on the cowl panel. This is a die-cut extrusion with pre-installed clips as original.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 20-1310-42
This Firewall To Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. A reproduction using the correct profile dense rubber extrusion.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1456-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3008-43
This Firewall To Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 70-4014-42
This Firewall To Hood Weatherstrip - Cowl Lacing comes with pre-drilled mounting holes and mounting clips installed. Made of high-quality EPDM rubber and to the original design for a factory like fit and appearance.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 20-1860-42
This Firewall To Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the closing hood and the vehicle firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3006-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. This seal mounts with installation tacks at the rear of the engine bay firewall directly to the body.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 70-3374-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. Measuring 67-1/2” long x 1-1/4” wide to provide complete coverage.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1088-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1457-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-2183-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part. This cowl lacing mounts with screws at the rear of the engine bay firewall directly to the body to seal between the hood and vehicle body cowl.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 20-1089-42
This Firewall To Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction using dense and sponge rubber extrusion with fasteners imbedded in place as original.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1086-42
This Firewall To Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. The weatherstrip is made of dense rubber and comes with pre-installed fastener clips.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 70-3137-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1087-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1085-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-2184-42
This Firewall to Hood Cowl Lacing Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This forty-four (44") inch weatherstrip installs at the rear of the engine bay to seal between the hood and the vehicle firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1855-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood closure and vehicle body cowl.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3007-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. A reproduction using dense rubber extrusion and tack fasteners.
Firewall To Hood Weatherstrip Set
p/n: 70-2873-43
This Firewall To Hood Weatherstrip Set is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip set installs at the rear of the engine bay to seal between the closing hood and the vehicle firewall.
Front Body Upper Pillar Drain Trough
p/n: 70-4212-73
This Front Body Upper Pillar Drain Trough pair is designed from the original part for superior fitment and seal. This left (LH) and right (RH) drain trough pair fits above the front upper door hinge, one per side.
Hood To Cowl Bumpers
p/n: 70-4744-42
This Hood To Cowl Bumper pair is a quality reproduction of the original factory part. This rubber bumper pair attaches to the body cowl to support / cushion the hood closure.
Hood to Cowl Dense Rubber Weatherstrip with Peel-N-Stick
1/4" x 3/4" inch Peel-N-Stick dense rubber cushion strip. Typically used for Hood To Cowl weatherstrip applications. Available in ten (10) or fifteen (15) feet lengths.
Hood to Cowl Fabric Lacing
p/n: 20-2022-43
This Hood To Cowl Fabric Lacing is designed from the original part for superior fitment and seal. This lacing attaches to the cowl at the rear of the engine bay to fit between the hood and cowl with hood closure.
Hood to Cowl Filler Seal
p/n: 20-2500-42
This Hood to Cowl Filler End Seal pair is designed from the original part for superior fitment and seal. Filler pieces are made from quality EPDM rubber to authentic original dimensions. These filler seals fit to the top outside corners on the left and right side of the hood to cowl.
Hood to Cowl Firewall Weatherstrip
p/n: 20-2752-42
This Hood to Cowl Firewall Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts with the included clips at the rear of the engine bay firewall directly to the body.
Hood To Cowl Rear Weatherstrip
p/n: 70-4692-43
This Hood To Cowl Rear Weatherstrip is designed from the original part for superior fitment and seal. A reproduction manufactured to the original profile and design specifications. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Side Extension Filler
p/n: 70-2258-43
This Hood to Cowl Side Extension Filler pair is fully molded from soft EPDM sponge rubber with all original details.
Hood To Cowl Side Weatherstrips
p/n: 60-0091-42
This Hood To Cowl Side Weatherstrip pair is molded with all original details. One (1) pair required per car. Length: 11 inches.
Hood to Cowl Sponge Rubber Weatherstrip with Peel-N-Stick
5/16" x 3/4" inch Peel-N-Stick sponge rubber cushioning strip. Typically used for hood to cowl applications. Available in ten (10) or fifteen (15) foot lengths.
Hood To Cowl Weatherstrip
p/n: 70-4835-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 70-3266-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.