Sash Channel Weatherstrip
p/n: 60-0690-58
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Side Window Bumper
p/n: 40-0116-70
Pad, side window anti-rattle. Five sixteenths (5/16) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal.
Side window bumper
p/n: 20-2783-62
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.
Side Window Bumper
p/n: 70-3428-62
Pad, side window inside anti-rattle. Three eights (3/8) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal. Six (6) required per truck
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
Side Window Glass Rear Weatherstrips
p/n: 82-0157-68
This Side Window Glass Rear Weatherstrip pair installs on the rear quarter section and seals the back edge of the door window to the body. Made from top quality rubber for durability and a like factory seal.
Side Window Glass Rear Weatherstrips
p/n: 82-0158-68
This Side Window Glass Rear Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the rear vertical B-post edge of the side windows for coupe and hatchback models.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Stop Bumper - Large / Rear
p/n: 70-4930-62
This Side Window Stop Bumper is designed from the original part for an authentic fit, finish, and appearance. This larger (7/8 inch) bumper fits into the lower run channel at the rear and is the down stop for the door glass.
Side Window Stop Bumper - Small / Front
p/n: 70-4942-62
This Side Window Stop Bumper is designed from the original part for an authentic fit, finish, and appearance. This smaller (1/2 inch) bumper fits into the lower run channel at the front and is the down stop for the door glass.
Side Window Stop Bumpers - Four (4) Piece Set
p/n: 90-3743-90
These Side Window Stop Bumpers are designed from the original part for an authentic fit, finish, and appearance. These bumper stops fit into the lower run channel and serve as the down stop for the door glass.
Upper Division Post Bumper
p/n: 70-3554-62
Bumper, upper division post. Rubber with metal cores. Both R & L sides.
Vent Frame Deflector
p/n: 70-1792-62
Deflector, beneath vent frame.Length: 5.75 inches. Width: 1.0 inches.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Window Division Bar Filler
p/n: 70-2661-62
This Window Division Bar Filler is sold as a four (4) piece set for the upper and lower. This filler set fits into inside garnish molding between rear seat side window and rear side window.
Window Regulator Arm Roller
p/n: 70-4813-62
This Window Regulator Arm Roller is designed from the original part for superior fitment and function. This nylon roller fits to the window regulator arm to lower and raise the side windows.
Window Sash Channel
p/n: 20-1909-62
This Window Sash Channel is designed from the original part for superior fitment and seal. Thirty-four and three-fourths (34-3/4") inch long EPDM rubber extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Window Sash Channel Weatherstrip
p/n: 20-3069-60
This Window Sash Channel Weatherstrip is designed from the original part for superior fitment and seal. Thirty six (36) inch long roll. One (1) roll required per window.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Windshield A-Pillar Post Weatherstrips
p/n: 82-0155-68
This Windshield A-Pillar Post Weatherstrip pair is designed from the original part for superior fitment and seal. These windshield frame weatherstrips install on the A-pillar post to seal the front edge of door window to the body.