Hydraulic Window Lift Grommet
p/n: 70-0643-21
Grommet, window lift hydraulic lines through floor panel, 2-hole style (for cars requiring single-hole style, see our #70-0642-21).Length: 1.5 inches.
Inner Side Window Bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.
Lower Door Glass Bumper
p/n: 20-1172-71
This Lower Door Glass Bumper is designed from the original part for superior fitment. If your door window goes too low or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Power Window Switch Bezel Pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Push-Out Window Frame Gasket
p/n: 70-4132-81
This Push-Out Window Frame Gasket is for the side OR rear push-out windows and has properly molded corners for a precise, factory fit. Up to six (6) used per van.
Push-Out Window Gasket Set
p/n: 90-0153-81
This Push-Out Window Gasket Set is for the Side OR Rear push-out windows. This three (3) piece kit includes the push-out window frame gasket and the inner and outer window glass weatherstrip.
Push-Out Window Weatherstrip
p/n: 70-4183-76
This Push-Out Window Weatherstrip mounts around the full perimeter of the glass and will flex around the window corners. A replacement for the original part offering a precise fit.
Push-Out Window Weatherstrip
p/n: 70-4751-76
This Push-Out Window Weatherstrip is designed from the original part for superior fitment, appearance and seal. This window weatherstrip fits to the body around the window opening to seal the push out window when closed.
Quarter Window Bumper
p/n: 70-1583-62
Bumper, quarter window stop on sash channel.Length: .8125 inches. Width: .75 inches. Height: .50 inches.
Quarter Window Filler
p/n: 20-3085-62
Seal assembly. Installs on body below rear quarter glass to body weatherstrip.
Quarter Window Vertical Leading Edge
p/n: 20-1656-76
This Quarter Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment, finish and function. This part fits Ford convertible only and is the weatherstrip that holds the quarter window glass in the frame.
Quarter Window Weatherstrip End Fillers
p/n: 70-4711-79
This Quarter Window Weatherstrip End Filler pair is designed from the original part for an authentic fit, finish, and function. Filler strips install at rear on inner panel at back end of the quarter window beltlines on convertible models.
Rear Door Window Upper Seal
p/n: 70-4198-79
This Rear Door Window Upper Seal pair is designed from the original part for superior fitment and sealing. This rectangular shaped seal pair mounts to the rear door at the upper front and over the rear side window.
Rear of Door Run Channel Seals - Convertible & T-Top
p/n: 70-4654-58
This Rear of Door Run Channel Seal pair is designed from the original part for superior fitment, finish and function. This window run channel seal fits at the end of the side window glass run channel. Molded as left and right.
Rear Quarter Window Bumper
p/n: 70-0688-62
Bumper, rear quarter window on door lock pillar. One and one fourth (1-1/4) inch square with metal core. Two (2) per car.Length: 1.375 inches.
Rear Quarter Window Bumper
p/n: 50-0399-62
Bumper, rear quarter window stop (lower) on window guide. Both upper and lower on some models. Three fourths (3/4) inch high. Compare to our #50-0400-62.
Rear Quarter Window Bumper
p/n: 50-0400-62
Bumper, rear quarter window stop (upper) on window guide. Both upper and lower on some models. Compare dimensions to our #50-0399-62.Length: .9375 inches.
Rear Quarter Window Bumper
p/n: 70-1096-62
Bumper, rear quarter window. Made of molded neoprene rubber with steel washer core. Two (2) per car.Length: 1.0625 inches.
Sash Channel Weatherstrip
p/n: 60-0690-58
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Side Window Bumper
p/n: 40-0116-70
Pad, side window anti-rattle. Five sixteenths (5/16) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal.
Side window bumper
p/n: 20-2783-62
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.
Side Window Bumper
p/n: 70-3428-62
Pad, side window inside anti-rattle. Three eights (3/8) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal. Six (6) required per truck
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
Side Window Glass Rear Weatherstrips
p/n: 82-0157-68
This Side Window Glass Rear Weatherstrip pair installs on the rear quarter section and seals the back edge of the door window to the body. Made from top quality rubber for durability and a like factory seal.
Side Window Glass Rear Weatherstrips
p/n: 82-0158-68
This Side Window Glass Rear Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the rear vertical B-post edge of the side windows for coupe and hatchback models.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Stop Bumper - Large / Rear
p/n: 70-4930-62
This Side Window Stop Bumper is designed from the original part for an authentic fit, finish, and appearance. This larger (7/8 inch) bumper fits into the lower run channel at the rear and is the down stop for the door glass.
Side Window Stop Bumper - Small / Front
p/n: 70-4942-62
This Side Window Stop Bumper is designed from the original part for an authentic fit, finish, and appearance. This smaller (1/2 inch) bumper fits into the lower run channel at the front and is the down stop for the door glass.
Side Window Stop Bumpers - Four (4) Piece Set
p/n: 90-3743-90
These Side Window Stop Bumpers are designed from the original part for an authentic fit, finish, and appearance. These bumper stops fit into the lower run channel and serve as the down stop for the door glass.
Upper Division Post Bumper
p/n: 70-3554-62
Bumper, upper division post. Rubber with metal cores. Both R & L sides.
Vent Frame Deflector
p/n: 70-1792-62
Deflector, beneath vent frame.Length: 5.75 inches. Width: 1.0 inches.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Window Division Bar Filler
p/n: 70-2661-62
This Window Division Bar Filler is sold as a four (4) piece set for the upper and lower. This filler set fits into inside garnish molding between rear seat side window and rear side window.
Window Regulator Arm Roller
p/n: 70-4813-62
This Window Regulator Arm Roller is designed from the original part for superior fitment and function. This nylon roller fits to the window regulator arm to lower and raise the side windows.