Window Sash Channel
p/n: 20-1909-62
This Window Sash Channel is designed from the original part for superior fitment and seal. Thirty-four and three-fourths (34-3/4") inch long EPDM rubber extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Channel Filler Weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Channel filler weatherstrip
p/n: 20-2575-62
Seal, door glass and window frame. Retains glass in frame. Enough for one window only.
Channel Filler Weatherstrip
p/n: 20-2091-62
This Channel Filler Weatherstrip is designed from the original part for superior fitment and seal. This door glass to body filler seal fits in the metal channel that holds the glass piece. Sold in a 36" strips.
Side Window Stop Bumpers - Four (4) Piece Set
p/n: 90-3743-90
These Side Window Stop Bumpers are designed from the original part for an authentic fit, finish, and appearance. These bumper stops fit into the lower run channel and serve as the down stop for the door glass.
Hydraulic Pump Mounting Pad
p/n: 70-0986-62
Mounting bracket and pad, for hydraulic pump. Number used as required.Length: 1.75 inches. Width: .8125 inches.
Hydraulic Pump Mounting Pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Front of Door To Window Seals
p/n: 70-4765-79
This Front Of Door to Window Seal pair is designed from the original part for superior fitment and seal. This is the door seal that mounts at the front of the door and seals where the door glass comes through.
Front Of Door To Window Seals
p/n: 20-2838-79
This Front Of Door to Window Seal pair is designed from the original part for superior fitment and seal. This is the door seal that mounts at the front of the door and seals where the door glass comes through.
Quarter Window Vertical Leading Edge
p/n: 20-1656-76
This Quarter Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment, finish and function. This part fits Ford convertible only and is the weatherstrip that holds the quarter window glass in the frame.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Front of Vent Window to Door Seals
p/n: 20-2786-62
These Front of Vent Window to Door Seals are installed at the front of the door and next to the door weatherstrip. Sold as a pair.
Door Flipper Stops
p/n: 70-2853-62
This Door Flipper Stop pair is designed from the original part for superior fitment and function. These rear flipper stops mount inside the flipper opening at the very rear of the door flipper.
Push-Out Window Weatherstrip
p/n: 70-4751-76
This Push-Out Window Weatherstrip is designed from the original part for superior fitment, appearance and seal. This window weatherstrip fits to the body around the window opening to seal the push out window when closed.
Hydraulic Window Lift Grommet
p/n: 70-0643-21
Grommet, window lift hydraulic lines through floor panel, 2-hole style (for cars requiring single-hole style, see our #70-0642-21).Length: 1.5 inches.
Rear Quarter Window Bumper
p/n: 70-1096-62
Bumper, rear quarter window. Made of molded neoprene rubber with steel washer core. Two (2) per car.Length: 1.0625 inches.
Fastback Quarter Window Lower Pivot Covers
p/n: 20-2787-62
These Fastback Quarter Window Lower Pivot Cover are designed from the original part for superior fitment, finish and function. The cover pair installs on pivot rod at fiberglass interior panel.
Push-Out Window Weatherstrip
p/n: 70-4183-76
This Push-Out Window Weatherstrip mounts around the full perimeter of the glass and will flex around the window corners. A replacement for the original part offering a precise fit.
Hydraulic Window Lift Grommet
p/n: 70-0642-21
Grommet, window lift hydraulic line through floor panel. Single hole type (for two (2) hole type, see our #70-0643-21).Length: 1.5 inches. Width: 1.
Window Division Bar Filler
p/n: 70-2661-62
This Window Division Bar Filler is sold as a four (4) piece set for the upper and lower. This filler set fits into inside garnish molding between rear seat side window and rear side window.