Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
Door Glass Bumper
p/n: 20-2088-62
This Door Glass Bumper is designed from the original part for superior fitment and usage. This bumper installs into garnish molding opening holes.
Door Glass Bumper
p/n: 20-2089-62
This Door Glass Bumper is designed from the original part for superior fitment and usage. This bumper installs in the door opening holes.
5/16" Side Window Bumper
p/n: 33-0516-71
This Side Window Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as an anti-rattle door window garnish molding. Two (2) required per door.
Inner Side Window Bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.
Window Regulator Arm Roller
p/n: 70-4813-62
This Window Regulator Arm Roller is designed from the original part for superior fitment and function. This nylon roller fits to the window regulator arm to lower and raise the side windows.
3/8" Side Window Weatherstrip
p/n: 70-0079-58
Weatherstrip, side window lower edge. Available by the foot.
5/16" Sash Channel Weatherstrip
p/n: 70-0585-58
This Sash Channel Weatherstrip is used for the outer side windows. Available by the foot.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door Glass Bumper
p/n: 20-1170-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Lower Door Glass Bumper
p/n: 20-1172-71
This Lower Door Glass Bumper is designed from the original part for superior fitment. If your door window goes too low or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Side Window Stop Bumper - Small / Front
p/n: 70-4942-62
This Side Window Stop Bumper is designed from the original part for an authentic fit, finish, and appearance. This smaller (1/2 inch) bumper fits into the lower run channel at the front and is the down stop for the door glass.
Door Glass Bumper
p/n: 20-1171-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Side Window Bumper
p/n: 70-3428-62
Pad, side window inside anti-rattle. Three eights (3/8) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal. Six (6) required per truck
Side Window Stop Bumper - Large / Rear
p/n: 70-4930-62
This Side Window Stop Bumper is designed from the original part for an authentic fit, finish, and appearance. This larger (7/8 inch) bumper fits into the lower run channel at the rear and is the down stop for the door glass.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
3/8" Channel filler weatherstrip
p/n: 70-2642-57
Channel filler weatherstrip. Available by the foot.
Quarter Window Bumper
p/n: 70-1583-62
Bumper, quarter window stop on sash channel.Length: .8125 inches. Width: .75 inches. Height: .50 inches.
1" Quarter Window Lift Grommet
p/n: 32-0098-21
This Quarter Window Lift Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
7/16" Vent Window Filler Strip
p/n: 70-2324-57
This Vent Window Filler Strip installs in the vent window metal frame to hold the glass. Available by the foot.
Side Window Bumper
p/n: 40-0116-70
Pad, side window anti-rattle. Five sixteenths (5/16) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal.
5/8" Channel filler weatherstrip
p/n: 30-0507-57
Seal, door window frame, upper and rear. Used on some open models with metal frame around glass. Available by the foot.
9/16" Window Gasket Weatherstrip
p/n: 60-0059-83
This Window Gasket Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be used with 1/4" glass in a 3/8" channel.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
9/16" Channel filler weatherstrip
p/n: 70-0489-58
Weatherstrip, channel filler, door window sash channel and some quarter window sash channel. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary. Available by the foot.
Rear Quarter Window Bumper
p/n: 50-0399-62
Bumper, rear quarter window stop (lower) on window guide. Both upper and lower on some models. Three fourths (3/4) inch high. Compare to our #50-0400-62.
1/2" Channel Filler Weatherstrip
p/n: 30-0154-57
Filler, for glass channel for convertible type windows with metal frame around one fourth (1/4) inch glass. Available by the foot.
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
Rear Quarter Window Bumper
p/n: 50-0400-62
Bumper, rear quarter window stop (upper) on window guide. Both upper and lower on some models. Compare dimensions to our #50-0399-62.Length: .9375 inches.
1" Sash Channel Weatherstrip
p/n: 50-0528-62
Weatherstrip, door window sash channel. Available by the foot.
2" Sash channel filler strip
p/n: 70-1693-57
Filler, door window, lower window sash. Use as required for windows with bolt-on sash channels. Available by the foot.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
Glass up stop bumper
p/n: 70-3623-62
Front door glass up stop bumper. For models w/out power vent windows. Use two (2) or four (4) per vehicle. Refer to your vehicle to see how many are required.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side window bumper
p/n: 20-2783-62
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Window Sash Channel Weatherstrip
p/n: 20-3069-60
This Window Sash Channel Weatherstrip is designed from the original part for superior fitment and seal. Thirty six (36) inch long roll. One (1) roll required per window.