Spring Shackle Bushing
p/n: 30-0420-32
This Spring Shackle Bushing is designed from the original part for superior fitment and function. Six (6) per car. Packard's "self flanging" type.
Rear Leaf Spring Shackle Assembly
p/n: 20-1834-32
This Rear Leaf Spring Shackle Assembly is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Spring shackle bushing
p/n: 30-0090-32
Bushing, spring shackle, for shackle and eye leaf of rear spring. Eight (8) required per car.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Spring Shackle Bushing
p/n: 30-0076-32
Bushing, spring shackle, front spring, front end; or rear spring, rear end. Two and one eighth (2-1/8) inch long. Sixteen (16) required per car.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Rear Leaf Spring Mounting Center Insulator Pad
p/n: 20-2984-32
This Rear Leaf Spring Mounting Center Insulator Pad is an exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle.
Spring shackle bushing
p/n: 70-0444-32
Bushing, rear spring shackle, upper. Four (4) required per car.
Rear Spring Pad
p/n: 27-0010-35
Pad, rear spring insulator for one and three fourths (1-3/4") inch wide springs. Four (4) per vehicle.
Leaf Spring Clamp Liner Set
p/n: 20-1272-32
A six (6) piece Leaf Spring Clamp Liner Set molded with durable EPDM rubber. These liners are used on Front and / or Rear Leaf Springs on the Driver's or Passenger side.
Rear Leaf Spring Mounting Center Insulator Pad
p/n: 20-2733-32
This Rear Leaf Spring Mounting Center Insulator Pad is an exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Spring or Stabilizer Bushing
p/n: 11-0020-35
Bushing, spring bracket on frame (Auburn and Cord 810 & 812). Also used as a grommet, front stabilizer bar (Graham models 116 & 120). Fully molded rubber.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Torsion bar bushing
p/n: 20-0670-36
Bushing, front radius rod. Front and rear. Four (4) required per Truck.
Radius Arm Bushing
p/n: 20-0671-36
This Radius Arm Bushing is a quality reproduction of the original factory part. The bushing fits at the frame end of the radius rod on 4-Wheel Drive models. Requires two (2) bushings per side with four (4) total per vehicle.
Rear Spring Pad
p/n: 30-0452-32
Insulator, rear spring leaf clip. Seven and one half (7-1/2) inch long, customer may trim for shorter lengths. May use up to eight (8) per car.
Spring Shackle Bushing Set
p/n: 20-2481-33
This Spring Shackle Bushing Set is for the front of the rear leaf spring. Two (2) kits required per car.
Front Coil Spring Insulator
p/n: 20-0203-32
This Front Coil Spring Insulator is designed from the original part for superior fitment, finish, and function. This spring insulator installs to prevent metal to metal contact at the top and bottom of the coil spring mounting points.
Rear Spring Eye Bushing
p/n: 60-0208-32
This Rear Spring Eye Bushing pair is designed from the original part for superior fitment and function. Bushings are for the rear spring, shackle eye, and spring eye. Up to twelve (12) per car.
Rear Leaf Spring & Shackle Bushing
p/n: 70-0182-32
This Rear Leaf Spring Bushing is designed from the original part for superior fitment and function. Bushing is for the rear leaf spring front or rear spring to shackle. Two bushings pushed together form one complete bushing. May require eight (8) or twelve (12) each depending or vehicle model if replacing all bushings.
Spring eye bushing
p/n: 10-0131-35
Bushing, spring eye, both eye leaf and shackle. Front and rear.Qty Required:20 Twelve (12) required per front, eight (8) required per rear.