Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Front Suspension Bumper
p/n: 40-0250-32
Bumper, front suspension, lower arm. Two (2) per car.Width: 3.0 inches. Height: 1.625 inches.
Axle Rebound Pad
p/n: 30-0371-32
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Front Spring Bumper
p/n: 30-0517-32
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Front Suspension Rebound Pad
p/n: 50-0083-32
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Axle Rebound Pad Service
p/n: 10-0003-35
Pad, rear axle rebound, perfect duplication. Length: 4.0 inches. Height: 1.25 inches.
Axle Rebound Pad Service
p/n: 70-0502-32
Bumper, rear spring to frame, two (2) per car.Width: 2.5 inches. Height: 2.5 inches.
Axle Rebound Pad
p/n: 70-0238-32
Pads, axle rebound, rear two and one fourth (2-1/4) inches diameter by three (3) inches high.Height: 3.0 inches.
Axle Rebound Pad
p/n: 10-0002-35
Pad, front axle rebound, including bolt hole. Excellent copy, highest grade material.Width: 2.25 inches. Height: 1.50 inches.
Front Suspension Bumper
p/n: 27-0080-32
This Front Suspension Bumper, front suspension lower A-arm, is made from high-quality EPDM rubber for a precise, factory fit.
Front Spring Bumpers
p/n: 30-0087-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Front Suspension Bumper
p/n: 70-1022-32
Bumper, front suspension, lower on spring seat. Made with long lasting Buna rubber.1958: Also used on other models with air suspension.Width: 1.875 inches.
Lower Suspension Arm Dust Seal Set
p/n: 70-0865-32
This four (4) piece Lower Suspension Arm Dust Seal Set is fully molded of high-quality EPDM dense rubber for durability and proper fitment. These seals are used to protect your lower suspension arm bushings from dust and debris.
Upper Suspension Arm Dust Seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Axle Rebound Pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Ride regulator control grommet
p/n: 70-0639-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car. Made without rod hole. You cut rod slot as required at installation.
Front Spring Bumpers
p/n: 30-0120-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Axle Rebound Pad
p/n: 27-0081-32
Bumper, rear axle on leaf spring.Width: 3.25 inches. Height: 4.75 inches.
Front Spring Bumper
p/n: 50-0238-35
Bumpers, front spring, Two (2) per car.Width: 2.0 inches. Height: 1.75 inches.
Radius Arm Bushing and Axle Set
p/n: 20-0780-32
This Radius Arm Bushing Set is a quality reproduction of the original factory part. This eight (8) piece bushing set fits four-wheel (4WD) drive trucks and Bronco.
Axle Rebound Pad
p/n: 50-0051-35
Pad, axle rebound, ring type, usually retained by leather straps or clip & bolt.