Rear axle bushing
p/n: 25-0081-32
Insulators, rear axle housing, upper and lower. Four (4) piece set.
Rear Axle Outer Bumper
p/n: 20-2729-32
This Rear Axle Outer Bumper is designed from the original part for superior fitment and function. This dense rubber bumper mounts on frame rail. Push-in type installation. Two (2) required per vehicle.
Rear Axle Outer Bumper
p/n: 20-2730-32
This Rear Axle Outer Bumper is designed from the original part for superior fitment and function. This dense rubber bumper mounts on frame rail. Push-in type installation. Two (2) required per vehicle.
Rear Axle Suspension Bumper
p/n: 70-2638-35
This Rear Axle Suspension Bumper is fully molded with new rubber vulcanized to new steel cores. Used on all models with conventional spring suspension.
Rear Spring and Axle Bumper
p/n: 20-1287-32
This Rear Spring and Axle Bumper is designed from the original part for superior fitment and function. The bumper mounts on the bracket above the center of the rear spring on each side of the vehicle.
Rear spring bumper
p/n: 70-2359-32
Bumper, rear spring. Fully molded with molded in attaching nuts like original.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Rear spring bumper service
p/n: 60-0279-35
Bumper, rear spring on frame. Revulcanization service only.
Rear Spring Bumper Service
p/n: 60-0425-32
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Rear Spring Bumpers
p/n: 60-0179-35
This Rear Spring Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Mounts to the frame for the rear springs. An assembly with rubber vulcanized to steel as original.
Ride Regulator Control Grommet
p/n: 70-0332-33
Grommets, ride regulator control rod through fender splash shield. Two (2) required per car.Length: 2.4375 inches. Width: 2.0 inches.
Ride Regulator Control Grommet
p/n: 70-0344-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car.Length: 5.875 inches. Width: 1.75 inches.
Ride regulator control grommet
p/n: 70-0639-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car. Made without rod hole. You cut rod slot as required at installation.
Steering Column Spacer
p/n: 60-0563-32
Spacer, steering column to dash at U-clamp.Length: 2.50 inches.
Support Arm Bumper
p/n: 50-0261-32
Bumper, steering knuckle support upper arm (for front shock absorber arm).Width: 1.5 inches.
Support Arm Bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Suspension Bushing
p/n: 70-3345-35
Bushing, rear shackle to body insulating mounts, upper. This is a four (4) piece set. Replaces OEM # 397225
Suspension Bushing
p/n: 30-0385-36
Bushing and pin assembly, cartridge, Inlox type, front wheel lower support arm inner pin. Shipped with instructions for re-installing.Length: 5.75 inches.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Suspension bushing
p/n: 30-0335-36
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Suspension Bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Track Bar Bushing
p/n: 25-0080-32
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Traction Bar Bumper
p/n: 70-2293-35
This Traction Bar Bumper is designed from the original part for superior fitment and function. An excellent reproduction of part found on models with radius rod traction bars.
Upper Control Arm Shaft Set
p/n: 20-1278-32
This three (3) piece Upper Control Arm Shaft Set is designed from the original part for superior fitment and performance. Renew the performance of your aged and worn front suspension to restore the ride of your classic vintage vehicle.
Upper Suspension Arm Dust Seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.