Luggage rack grommet
p/n: 70-0287-46
Grommets, luggage rack brace rod through body. Styles with luggage rack arms.
Rear Panel Weatherstrip
p/n: 70-3651-85
This Rear Panel Weatherstrip seals the front edge of the trunk near the convertible top. Contains fully molded ends with attached bolts for easy and accurate installation. Two (2) strips required to seal upper and lower.
Upper Rear Deck Lid Corner Seals
p/n: 70-4145-87
This Upper Rear Deck Lid Corner Seal pair is designed from the original parts for superior fitment and seal. These seals mount directly to the body on the right side and left side at each corner to seal against the upper rear deck lid.
Trunk Weatherstrip Corners
p/n: 70-1038-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Luggage Rack Grommet
p/n: 17-0021-46
Grommet, luggage rack support arm through body.Length: 2.25 inches. Width: 1.25 inches.
Luggage Rack Grommet
p/n: 70-0403-46
Grommets, luggage rack arms through sheet metal, special tall type.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Luggage Compartment Door Bumper
p/n: 70-4143-87
This Luggage Compartment Door Bumper is designed from the original part for superior fitment and function. This bumper mounts within the luggage compartment to act as a Stop for the luggage compartment door closure.
Luggage Rack Pad
p/n: 20-1469-45
Pads, roof luggage carrier to roof. Sixty three (63) inches long. Set of six (6) pads.
Rumble Seat Weatherstrip
p/n: 14-0051-87
Weatherstrip or rubber buffer, rumble seat opening notch-out on perimeter of opening near water catch rail. Two (2) used per car.
Rear Bumper to Lower Back Panel Splash Shield
p/n: 70-3655-47
This Rear Bumper To Lower Back Panel Splash Shield is designed from the original part for superior fitment and seal. This filler attaches to the rear edge of the lower deck lid panel.
Trunk Bumper
p/n: 50-0163-87
Bumper, trunk. Brass core, screw held. Two (2) per car.Length: 1.5 inches. Width: .75 inches.
Decklid Lock Bumper
p/n: 40-0361-85
This Decklid Lock Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Convertible Top Deck Lid Cover Weatherstrip
p/n: 70-3939-67
This Convertible Top Deck Lid Cover Weatherstrip is designed from the original part for a superior fitment and seal. This rubber seal mounts around the full perimeter of the soft top storage compartment.
Trunk Bumper
p/n: 40-0082-85
Bumper, trunk lid, rubber. Retained by two (2) screws (not included).Width: 2.50 inches. Height: 1.625 inches.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This Golf Bag Door Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Rumble Seat Lid Bumper Pad
p/n: 70-0278-87
Side pads, rumble seat lid, right and left. Length: 1.125 inches. Width: .6875 inches.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Rumble Seat Lid Bumper Pad
p/n: 30-0275-44
Bumpers, rumble seat stop bracket. Self-retaining type as original.Length: 1.1875 inches. Width: .75 inches. Height: .375 inches.
Rumble Seat Lid Corner Pad
p/n: 70-0152-87
Pads, rumble seat lid corners, original rounded triangle shape.Length: 1.5 inches. Width: .4375 inches.
Convertible Top Decklid Weatherstrip
p/n: 70-3950-67
This Convertible Top Decklid Weatherstrip is designed from the original part for a superior fitment and seal. This rubber seal mounts around the full perimeter of the soft top storage compartment.
Rumble Seat Lid Corner Pad
p/n: 70-0120-87
Pad, rumble seat lid corner, Compare with our #60-0191-87. Length: .75 inches.
Rumble Seat Lid Corner Pad
p/n: 70-0048-87
Pads, rumble seat lid corners original style, rounded triangular shape.Width: 1.25 inches.
Clutch, Brake Pedal or Rumble Seat Pads
p/n: 20-0325-22
This reproduction Pad pair easily screws on the clutch and brake pedal arms for a precise, factory fit. Pads with pyramid design like original. Used as clutch and brake pedal pads for all models. Used as a rumble seat step pad for cars so equipped.
Trunk Bumpers - Convertible
p/n: 70-4663-87
This Trunk Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the trunk decklid to support / cushion the trunk lid closure onto the vehicle body.
Rumble Seat Lid Bumper Pad
p/n: 40-0297-85
Bumper, rumble seat lid. Sometimes used on trunk. One half (1/2) inch by one (1) inch by one (1) inch. Two (2) per car.Length: 1.0 inches. Width: 1.0 inches.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Rumble Seat Lid Bumper Pad
p/n: 13-0006-87
Pad, rumble seat lid bumper, one and three sixteenths (1-3/16) inch square.Width: 1.1875 inches. Height: .5625 inches.
Trunk Decklid Bumper Stop
p/n: 82-0160-87
This Trunk-Decklid Bumper Stop is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure.
Decklid Top Cover Weatherstrip
p/n: 70-3922-67
This Decklid Top Cover Weatherstrip is designed from the original part for a superior fitment and seal. This weatherstrips mounts around the full perimeter of the soft top storage compartment.
Trunk Bumper
p/n: 50-0546-87
Bumper, trunk. On side near hinge end. Made with metal core.Width: 1.625 inches. Height: 1.0 inches.
Trunk Deck Lid Rubber Bumpers
p/n: 70-2601-42
This Trunk Deck Lid Rubber Bumper pair is designed from the original part for superior fitment, finish and function. The correct OE style trunk deck lid rubber bumpers stoppers. Two required per car.
Trunk Hinge Gaskets - Convertible
p/n: 70-4657-87
This Trunk Hinge Gasket pair is designed from the original part for superior fitment, finish and function. On Convertibles the gasket pair install between the plastic hinge cover and the trunk lid on the exterior (near the rear window).
2-1/4" Trunk Floor Pan Plug
p/n: 70-2598-87
This Trunk Floor Pan Plug is designed from the original part for superior fitment and seal. This plug is made from high quality EPDM dense rubber to provide excellent durability.
1-13/16" Trunk Floor Pan Plug
p/n: 70-2599-87
This Trunk Floor Pan Plug is designed from the original part for superior fitment and seal. This plug is made from high quality EPDM dense rubber to provide excellent durability.
Trunk Decklid Adjustable Bumper
p/n: 70-2708-87
This Trunk Decklid Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure. Screws into trunk. Two (2) required per car.
Trunk Bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
Brown Trunk Bumper
p/n: 30-0299-89
Cap for covering fender bolt, trunk interior. Brown rubber.Height: .8125 inches.
Trunk Decklid Bumpers
p/n: 70-2044-87
This Trunk Decklid Bumper pair is designed from the original part for superior fitment, finish and function. These rubber bumpers attach to the trunk decklid to support / cushion lid closure.
Trunk Bumper
p/n: 70-2741-87
Bumpers, adjustable trunk. Screws into trunk. Two (2) required per car.
Trunk - Decklid Bumper
p/n: 70-3528-87
This Trunk-Decklid Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure.
Trunk Bumper
p/n: 70-2612-87
This Trunk Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the rear body to support / cushion the Trunk / Decklid closure. Usually requires two (2) bumpers each per vehicle.
Tailgate Bumper
p/n: 70-2618-87
This Tailgate Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the tailgate closure. Usually requires two (2) bumpers each per vehicle.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Trunk Bumper
p/n: 70-2607-87
This Trunk Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the rear body to support / cushion the Trunk / Decklid closure. Usually requires two (2) bumpers each per vehicle.
7/8" Trunk Floor Pan Plug
p/n: 35-0402-87
This Trunk Floor Pan Plug is designed for floor construction holes and rest pad for the spare wheel area. Six (6) to eight (8) per car, as required.
1/2" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
1/4" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
3/16" Trunk Bumper
p/n: 33-0990-87
This Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Hood or Trunk Bumper
p/n: 34-0203-42
This Bumper is designed to be used for the trunk or hood. The bumper is molded with clearance for the attachment screw (not included).
Chrome Molding Washer
p/n: 60-0727-45
Washer, for attaching chrome moldings on body. Fits into metal cup retainer. Three fourths (3/4) inch diameter, use as required.
1" Wiring Grommet
p/n: 32-0401-45
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the license light wire through the trunk inner panel.