Upgrade your 1960-1987 Chevrolet C10/R10 with premium weatherstripping designed for a perfect factory fit. Our high-quality rubber seals protect against wind, rain, and road noise, ensuring a quieter, more comfortable ride while preserving your truck’s interior. Whether you're restoring a classic or replacing worn-out seals, our durable, precision-fit weatherstripping keeps the elements out and your truck looking great.
For installation assistance, we invite you to visit our YouTube channel for tips and ideas. If you need further assistance, please call 800-447-0849 or email us at cars@steelerubber.com.
Heat and Sound Insulator Underlayment
p/n: 70-4676-88
This single piece die-cut Heat and Sound Insulator Underlayment for floors lays under the carpeting's felt mat. This underlayment will decrease road noise and decrease heat inside the trucks interior compartment. Pre-cut and ready to be installed into your vehicle to improve driving comfort.
Window Felt Outer Beltline Weatherstrips
p/n: 80-0062-57
This is an Original material style outer side window horizontal weatherstrip set (also known as beltline weatherstrip). This ready to install two (2) piece beltline set includes only the outer seals (the part sealing the outside of the vehicle) for the side windows.
Vent Window Division Post Weatherstrips
p/n: 70-1923-56
This Front Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the vertical division bar with rivets and the vent glass closes against it.
Front Door Vent Window Weatherstrips
p/n: 70-1924-55
These Front Door Window Weatherstirps are the One-Piece style with the attached division post seal. They are molded as left and right and designed from the original parts for superior fitment and seal.
Vent Window Division Post Weatherstrips
p/n: 60-0585-56
This Front Door Vent Window Division Posts Weatherstrip pair is fully molded with a metal core and attachment holes. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Fuel Neck Grommet
p/n: 70-1942-41
Grommet, fuel filler neck. Off center flange style. Fully molded rubber. Three and one eighth inch (3 1/8") outside width by three and one fourth inch (3 1/4") outside length by two and one fourth inch (2 1/4") inside diameter by one inch (1") height.
1973-1978 Chevy And GMC Truck Factory Parts, CD
p/n: 07-1417-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Chevrolet and GMC Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Transmission Mount Service
p/n: 60-0465-25
Transmission mount. One (1) per car. Revulcanization service only.Length: 5.75 inches.
Hood to Cowl Weatherstrip
p/n: 70-1446-43
Weatherstrip, hood to cowl seal. Approximately fifty seven (57) inches of extruded rubber.
Inner Fender to Cowl Filler Set
p/n: 70-3356-45
This six (6) piece Inner Fender to Cowl Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit at rear of fender to cowl panel.
Window Gasket Locking Strip - Chrome
p/n: 70-1919-52
This chrome appearing Window Gasket Locking Strip is designed from the original part for superior fitment and seal. Locking strip serves as the front or rear window gasket retainer. Sixteen (16') foot length single piece, one application, for complete coverage.
Door Jamb Wire Loom Grommets
p/n: 70-4870-70
These Door Jamb Wire Loom Grommets go between the door and door jam and allow you to run wires or cables through them. They make great complements to power window kits, shaved door kits, or custom stereo installs.
Clutch or Brake Pedal Pad
p/n: 60-0467-22
This reproduction Clutch or Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Glass Run Channel - Vent Window Delete
p/n: 70-3891-58
This Glass Run Channel pair is for applications where the vent window has been eliminated. One pair fits both driver (Left) and passenger (Right) side doors.
Paint Reseal and Gasket Set
p/n: 70-4310-44
This Paint Reseal Gasket Set contains like original design reproductions for the vehicles specific exterior pieces. These reproductions are die-cut from quality materials to the original design for superior performance, durability, and a factory like fit.
Hood To Cowl Weatherstrip
p/n: 70-5062-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs on the firewall at the rear of the engine bay to seal between the hood and vehicle body cowl.
Window Locking Strip - Black
p/n: 70-1918-52
This Window Locking Strip is designed from the original part for superior fitment and function. Front or rear window retainer made from top quality black EPDM rubber. Available in 15ft lengths.
Clutch or Brake Pedal Pad
p/n: 60-0712-22
This reproduction Clutch or Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Steering Column Grommet
p/n: 70-3158-36
This Steering Column Grommet is designed from the original part for superior fitment and seal. This seal fits around the steering column at the toe board.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Radiator Bracket Cushion
p/n: 70-2554-31
Cushions, radiator support, upper. Fully molded, specially designed to duplicate original part.
Stabilizer Bar To Frame Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Cowl Vent Gasket
p/n: 60-0601-54
Side cowl vent seal. One eighth (1/8) inch thick high quality sponge design.Length: 8.50 inches. Width: 5.375 inches.
Radiator Bracket Cushion
p/n: 70-2555-31
Cushions, radiator support, lower. Fully molded, specially designed to duplicate original part.
Hood To Cowl Weatherstrip
p/n: 70-4835-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Vent Window Division Post Weatherstrips
p/n: 70-1921-56
This Front Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. These pieces mount on the vertical division post with rivets and seal as the vent glass closes against them. Fully molded with metal core and pre-drilled holes.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Kick Panel Vent Gaskets
p/n: 70-4919-88
This Kick Panel Vent Gasket pair is designed from the original part for superior fitment and function. Can be used on trucks with or without A/C.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Fuel Filler Neck Gasket
p/n: 70-4920-39
This Fuel Filler Neck Gasket is designed from the original part for superior fitment and seal. Machine stamped from quality materials to authentic original dimensions.
Inner Fender Seal
p/n: 60-0667-45
Seal, inner fender to frame. Extruded rubber strip replacement. Available by the foot.
Tie Rod End Dust Boot
p/n: 60-0096-32
This Tie Rod End Dust Boot is designed from the original part for an authentic fit, finish and function. Four (4) required per vehicle.
Shock Absorber Bushing
p/n: 60-0235-33
This Shock Absorber Bushing is fully molded and designed from the original part for superior fitment and durability. A plain cylinder type bushing with flat ends for shock absorber mounting.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
5/16" Door Bumper
p/n: 33-0293-71
Bumper, front door pillar, upper and lower. Replaces factory #3720168.
Steering Column At Floor Seal
p/n: 70-3768-88
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. Seal is machine die cut from sponge rubber to original specifications for a factory it. This part fits around the steering column to seal the column through the body floor pan.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
3/4" Firewall Grommet
p/n: 32-0263-17
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as license lamp wire through the body, parking brake front cable, and idler lever pull rod.
3/4" Door Weatherstrip
p/n: 70-0236-73
This weatherstrip was designed for 1964–1966 Chevrolet and GMC truck doors but with its generic shape, has many uses outside of its original purpose.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
Corner Joint Sleeves
p/n: 70-3720-52
Corner Joint Sleeve pair for the bottom corners of rear window gaskets that require a locking strip. These joint sleeves have a Chrome look to match the Mylar locking strip. Joint sleeves can also be painted black when using with the black rubber locking strip.
1/4" Multi-Purpose Bumper
p/n: 60-0734-71
This 9/16" Multi-Purpose Bumper is a quality reproduction of the original factory part. This bumper can also be used Door Lock Striker Plate, Window Glass Stops and License Plate.