Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Bumper
p/n: 30-0350-71
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 60-0032-71
Pad, door jamb. One (1) per door.Length: 1.25 inches. Width: .75 inches. Height: .875 inches.
Door Bumper
p/n: 17-0041-70
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Door Check Strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Door Check Strap
p/n: 40-0536-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing, molded-in steel shank and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Door Handle Grommet
p/n: 70-0009-69
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
Door or Side Window Weatherstrip
p/n: 30-0147-73
This quality dense rubber weatherstrip works as a Door Weatherstrip on certain Packard models with Dietrich closed bodies or as a Side Window Weatherstrip on certain Ford-Lincoln K models with Coachmaker bodies. Available by the foot.
Electrical terminal boot
p/n: 30-0061-21
Cover, starter cable terminal post inside to frame. Full detail and molded as original part.
Engine Mount Cushions
p/n: 70-0300-11
These Engine Mount Cushions are used as an intermediate engine mount for support bolts. Split in half if needed at installation. A four (4) piece set.
Engine Mount Pad
p/n: 11-0027-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Engine Mount Pad
p/n: 11-0026-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made from high-quality EPDM rubber for a precise, factory like fit. Two (2) required per car.
Engine Mount Pad
p/n: 70-1161-11
This Engine Mount Pad pair is designed from the original for an exact original configuration. For cars with round cone-type front mounts.
Engine Mount Pad
p/n: 70-1162-11
This Front Engine Mount Pad pair is designed for cars with round cone type front engines. For V-12 and V-16 models.
Engine Mount Pad
p/n: 11-0028-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Engine Mount Pad
p/n: 70-0977-11
This Engine Mount Pad pair is molded from a high-quality rubber. Designed from the original for an exact reproduction.
Engine Mount Pad
p/n: 11-0029-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Engine Mount Service - Revulcanization Only
p/n: 11-0018-11
This Revulcanization Service Only is designed to restore your Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Fender to Radiator Seal
p/n: 40-0085-44
This Fender to Radiator Seal is molded out of EPDM rubber Overall length is 11.25 inches.
Fender Well Pad
p/n: 15-0011-37
Pad, fender well for sidemounted spares. One (1) pair per fender.Length: 2.875 inches. Width: 2.875 inches. Height: .4375 inches.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Ferrule Installing Tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Firewall Grommet
p/n: 50-0272-20
This Firewall Grommet is used to run the water temperature indicator pipe through the dash. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 17-0045-20
This Firewall Grommet is designed as a firewall pass through for eight (8) wires or cables. For twelve (12) cylinder models only. For eight (8) cylinder models see our 17-0044-20.
Firewall Grommet
p/n: 25-0026-20
This Firewall Grommet is the six (6) hole type used to run wires, cables, or tubes through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 30-0093-21
This Firewall Grommet is used to run the ignition advance along with various rods and tubing through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet Set
p/n: 70-1147-21
This Firewall Grommet Set contains six (6) pieces intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Firewall Grommet Set
p/n: 70-1149-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Firewall Grommet Set
p/n: 70-1148-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Firewall Pass Through Grommet
p/n: 40-0522-21
This Firewall Pass Through Grommet is the rectangular large type. Designed from the original part for superior fit and seal.
Firewall Pass Through Grommet
p/n: 40-0523-21
This Firewall Pass Through Grommet is the smaller rectangular type. Made from high-quality dense rubber to provide excellent durability.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Apron Crossbar Grommet
p/n: 70-1130-45
Grommets, front splash apron crossbar.Width: 3.5 inches. Height: 3.6875 inches.
Front Apron Crossbar Grommet
p/n: 17-0002-45
This two (2) piece Front Apron Crossbar Grommet pair is for the left and right side. Made of a top quality EPDM Dense rubber to ensure durability.
Front Apron Crossbar Grommets
p/n: 70-1131-45
This Front Apron Crossbar Grommet pair is designed from the original part for superior fitment, finish and function. Width: 3-1/2" inches. Height: 3-1/2" inches.
Front Bow Weatherstrip
p/n: 30-0066-67
Pad, folding top, front frame to windshield. Five sixteenths (5/16) inch by one half (1/2) inch rectangular section, fifty (50) inches long. Length: 50.
Front Bow Weatherstrip
p/n: 70-0137-64
Weatherstrip, front bow-to-windshield, soft rubber, hollow body, proper screw holes, hinged flaps front and back.
Front Engine Cushion Set
p/n: 25-0037-11
This four (4) piece Front Engine Cushion Set is molded from a high-quality EPDM dense rubber. Designed from an original part for an exact reproduction.
Front Engine Mount Support Cushion
p/n: 70-0324-11
This Front Engine Mount Support Cushion is designed from an original part to correct specification for a correct fit and appearance.
Front Spring Bumper
p/n: 50-0238-35
Bumpers, front spring, Two (2) per car.Width: 2.0 inches. Height: 1.75 inches.
Front Spring Bumper
p/n: 50-0423-35
Bumper, front spring. Fits onto original bracket.Length: 2..125 inches. Width: 2.0 inches. Height: 1.875 inches.
Front spring mounting block
p/n: 11-0015-33
Shock insulator or mounting block, front spring, both ends. Four (4) piece set.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Fuel Neck Grommet
p/n: 40-0067-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Gearshift Floorplate
p/n: 40-0137-88
Floorplate, gearshift and handbrake cover. Steel core as original, with exact rubber pattern.Length: 13.125 inches. Width: 10.875 inches.
Gearshift Floorplate
p/n: 40-0017-88
Floorplate, gearshift and handbrake. Full metal insert as original.Length: 13.125 inches.
Gearshift Floorplate
p/n: 40-0156-88
Floorplate, gearshift and handbrake. Hole cover, grass core as original.Length: 12.50 inches. Width: 9.0 inches.
Gearshift Floorplate
p/n: 40-0058-88
Floorplate, gearshift and handbrake. Fine detail, metal core as original.Length: 8.125 inches.
Gearshift Floorplate
p/n: 17-0005-24
Floorplate, gearshift and handbrake, black rubber only.Length: 10.625 inches. Width: 8.875 inches.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This Golf Bag Door Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Handbrake Floorplate
p/n: 11-0005-24
Floor plate, handbrake lever. Brass core as original, fully detailed.
Headlight Bar Grommet
p/n: 11-0002-14
Grommet, headlight bar-to-radiator shell. Includes clearance groove, faithful detail. 1-1/8 inch inside diameter.
Headlight Bracket Pad
p/n: 50-0222-14
Headlight bracket-to-fender pad. POA #1245890-1, right and left.
Headlight Grommet
p/n: 40-0008-14
Grommets, headlight bar to shell. Slightly oval. One and one fourth (1-1/4) inch diameter hole.
Headlight Grommet
p/n: 40-0009-14
Grommet, headlight bar to shell. One and one fourth (1-1/4) inch round hole.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Headlight tube flange gasket
p/n: 50-0223-14
Headlight tube flange gasket. Two (2) per car. Replaces #1234556.
Hinge Pillar Weatherstrip
p/n: 70-0734-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hood Bumper
p/n: 60-0034-42
Bumper stop, hood, lower center. Two (2) required per vehicle.Length: 1.0 inches. Width: .75 inches. Height: .4375 inches.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Corner Pad
p/n: 34-1186-42
Pads, hood door corners, cup type.1931 Twenty (20) required. 1932 Twenty Four (24) required.Height: .375 inches.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Hood Latch Swivel Pad
p/n: 34-0408-42
Pad, hood latch swivel for hood latch pressure against hood corners. For screw or rivet.
Hood Ventilator Bumper Set
p/n: 70-0011-42
This forty (40) piece Hood Ventilator Bumper set is designed from the original parts for superior fitment and function. The set includes bumpers and rivets for one (1) hood.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.