Radiator Bracket Cushion
p/n: 70-2229-31
Radiator support bracket, insulator, lower. Two (2) used per car.Length: 4.5 inches.
Glovebox Door Check Grommet
p/n: 70-0467-88
Grommet, glovebox door check link, for one (1) inch slot in dash.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Firewall Grommet
p/n: 70-2067-20
This Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Headlight Mounting Pad
p/n: 50-0462-14
Headlight housing to fender gasket. Steel rule die-cut replacement for #1320452.
Parking Light Lens Gaskets
p/n: 70-3073-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Brake Pedal Pad - Automatic
p/n: 70-4589-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmission models. Detailed and finished to match the original appearance.
Radiator Mounting Insulator Pads
p/n: 70-2016-31
A Radiator Mounting Insulator Pad pair for use on the corners of the radiator. One (1) pair per side.
Door Handle Gasket Set
p/n: 70-0771-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Firewall Grommet
p/n: 50-0396-20
This Firewall Grommet is used to run the wiring harness and other various wires through the firewall. Designed from the original part for superior fit and seal.
Cornering, Signal and Parking Light Lens Gaskets
p/n: 70-3238-17
This Cornering, Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the cornering light lens and the cornering light housing or bezel.
Taillight Mounting Pad
p/n: 50-0410-15
Pad, taillight to fender. Width: 7.25 inches. Height: 4.0 inches.
Firewall Grommet
p/n: 50-0165-20
This Firewall Grommet is used to run the speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Firewall Grommet
p/n: 50-0239-20
This Firewall Grommet is used to run various lines through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 70-2066-24
This Firewall Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Taillight Lens Gasket
p/n: 50-0411-15
Gasket, taillight lens. Die cut three sixteenths (3/16) inch sponge rubber as original.Width: 6.25 inches. Height: 3.25 inches.
Fuel Filler Neck Grommet
p/n: 70-1439-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fits as original.
Door Bumper
p/n: 33-0449-71
Bumper, door, lower, held by one (1) screw and one (1) carrot retainer. Length: 1-1/8 inches. Width: 5/8 inches.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Body Mounting Pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Hood To Cowl Weatherstrip
p/n: 70-1694-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Side Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
1-3/8" Firewall Grommet
p/n: 50-0327-20
This Firewall Grommet is used to run the speedometer cable through the lower firewall. Designed from original parts for excellent workmanship.
Front Signal Light Lens Gaskets
p/n: 70-4048-16
This Front Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the front turn signal light lens and the front turn signal light housing or bezel.
Cornering Light Lens Gaskets
p/n: 70-4044-16
This Cornering Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the front cornering light lens and the front cornering light housing or bezel.
Directional Signal Light Lens Gaskets
p/n: 70-4043-16
This Directional Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the front Signal Light Lens and the front Signal Light Housing or Bezel.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Body Mounting Pad
p/n: 60-0119-48
This Body Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with metal core and metal bolt liner.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3062-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Firewall Grommet
p/n: 50-0535-20
This Firewall Grommet is used to run the speedometer cable and windshield washer lines through the firewall. Designed from original parts for excellent workmanship.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Side Window Stop Bumpers - Four (4) Piece Set
p/n: 90-3743-90
These Side Window Stop Bumpers are designed from the original part for an authentic fit, finish, and appearance. These bumper stops fit into the lower run channel and serve as the down stop for the door glass.
Cowl grill seal
p/n: 60-0679-54
Weatherstrip, cowl grill to firewall. Used on either end of cowl near fender. Die cut dense sponge rubber.
Door Handle Gasket Set
p/n: 50-0515-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Taillight Lens Gaskets
p/n: 70-3072-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-2798-45
This Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pair pieces are die cut from quality masticated rubber to authentic original dimensions. This filler pair fits over suspension a-arms and inside front inner fenders.
1-1/4" Firewall Grommet
p/n: 70-0198-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for excellent workmanship.
1-5/8" Firewall Grommet
p/n: 70-2064-20
This Firewall Grommet is used to run the vacuum hose and ignition resistor wire through the firewall. Designed from the original part for excellent workmanship.
1-5/8" Firewall Grommet
p/n: 70-2062-20
This Firewall Grommet is used to run the oil pressure and temperature line through the firewall. Designed from original parts for excellent workmanship
1-5/8" Firewall Grommet
p/n: 70-2063-20
This Firewall Grommet is used to run the speedometer cable line through the firewall. Designed from original part for excellent workmanship.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Door Handle Gasket Set
p/n: 70-3215-69
This four (4) piece Door Handle Gasket Set is designed from the original part for superior fitment and seal. Gaskets are precision die cut to the original specifications. This set is for two (2) door handles.
Hood To Cowl Weatherstrip
p/n: 70-2807-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Door Handle Gasket Set
p/n: 50-0560-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Trunk Bumper
p/n: 50-0546-87
Bumper, trunk. On side near hinge end. Made with metal core.Width: 1.625 inches. Height: 1.0 inches.
Hood Bumper
p/n: 50-0194-42
Bumper, hood side on fender ledge center. Self retaining type. See our #50-0095-42 for rear type.Height: 1.625 inches.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.