Cab To Frame Mount - Revulcanization Service Only
p/n: 70-2212-48
This Rear Cab To Frame Mount - Revulcanization Service Only is designed to restore your truck's rear cab mounts to a like new original condition. Please call or email for more service details and ordering.
Cab To Frame Mounting Pad Set
p/n: 20-0699-48
This Cab To Frame Mounting Pad Set is a thirty-two (32) piece set for the cab to frame mounting pads and bolts. For 2 W/D (wheel drive) trucks only. These frame pads are installed between the frame and the truck cab floor pans.
Radiator Support to Frame Pad Set
p/n: 20-0772-31
This eighteen (18) piece Radiator Mounting Pad Set is designed from the original parts for a factory like appearance and function. This set fits F100 2-wheel drive models, but will work for F-250 and F-350 models by adding extra metal washers.
Cab to Frame Mounting Pad Set
p/n: 20-0698-48
This twenty-six (2) piece Cab to Frame Body Mounting Pad set is designed from the original parts for superior fitment and function. This set is designed to mount your cab to the frame.
Body Mounting Pad
p/n: 70-0298-48
Pads, body mounting for front bracket, right and left. Three eighths (3/8) inch by two and three fourths (2-3/4) inch by four (4) inches with two (2) collars and retaining rings. Two (2) required per car.
Radiator mounting pad
p/n: 30-0121-31
Grommet, radiator cradle to frame tie rod. 1st type, with locating boss. One four (4) piece set required per car. See also our #30-0309-31.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Radiator Mounting Pad
p/n: 30-0209-31
Shim, radiator core mounting stud spacer. Fully molded rubber. Use as required. Comes as a pair of two (2). Two and seven eighths inch (2 7/8") square by five eighths inch (5/8") inside hole diameter by three eighths inch (3/8") height.
Body Mounting Pad Set
p/n: 70-2283-48
A three (3) piece Body Mounting Pad set to include replacement pads for the upper insulator, the middle insulator, and for the bottom cone shaped insulator. These body mounts install between the frame and the body floor pans.
Cab Bumper
p/n: 60-0510-48
Bumper, cab hold down bolts. Comes as a pair of two (2). Fully molded rubber.
Body Mounting Pad
p/n: 70-0299-48
Pad, body mounting, for body bracket. Two (2) collars and retaining rings. Four (4) per car.
Body Mounting Pad
p/n: 60-0412-48
Body bumpers, rear, at body hold-down bolt. Fully molded rubber. Comes as a pair of two (2). One and three fourths inch (1 3/4") outside length by one and one fourth inch (1 1/4") diameter by three eighths inch (3/8") inside hole diameter.
Body to Frame Isolator Mounting Pads
p/n: 70-3343-48
This two (2) piece Body to Frame Isolator Mounting Pad set is designed from the original part for superior fitment and seal. Pieces are made of fully molded EPDM rubber. Two (2) sets required per car.
Body Mounting Pad
p/n: 60-0383-48
Cushion assembly body mounting pad. Fully molded rubber with metal core, locating collar and metal bolt sleeve. Rectangular.
Front Fender to Apron Seal
p/n: 20-2504-45
This Front Fender to Apron Seal installs on the fender to inner apron. Excellent for when assembling front sheet metal. Sold as a fifteen (15) foot roll.
Body Mounting Pad
p/n: 70-0297-48
Pad, body mounting. Three eighths (3/8) inch by two (2) inch by three (3) inch with collar and retainer ring.
Body Mounting Pad
p/n: 30-0501-48
Pad, body mounting. Fully molded rubber with metal core. Number used varied according to body type.
Body to Frame Mounting Pad
p/n: 60-0188-48
This Body to Frame Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with a metal core, locating collar, and metal bolt. Two (2) required per vehicle.
Body Bolt Cushion
p/n: 27-0079-48
Pad, body bolt insulator. Metal core & locating collar covered with rubber. Number used varies per car. Two inch (2") square by seven eights inch (7/8") locating collar outside diameter by five eighths (5/8") locating collar inside hole diameter. Five eig
Body Mounting Pad
p/n: 27-0101-48
Pad, body mounting cushion. Metal core and locating collar covered with rubber.
Body Mounting Pad
p/n: 30-0500-48
Pad, body mounting. Fully molded rubber with locating collar and metal core. Number used varied according to body type.
Body Mounting Pad
p/n: 60-0382-48
Cushion assembly (body mounting pad). Rubber with metal core, locating collar and metal bolt as original. Metal bolt is removable, measures fifteen sixteenths inch (15/16") long when removed.
Body Mounting Pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Body Mounting Pad
p/n: 70-1749-48
This Body Mounting Pad is fully molded rubber with a metal core and locating collar. These frame pads are installed between the frame and the floor pans.
Body Mounting Pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Body Mounting Pad
p/n: 60-0028-48
Pad, front body mounting. Right angle style. Fully molded rubber. Four and one sixteenth inch (4 1/16") length by three and seven eighths inch (3 7/8") width by one half inch (1/2") inside hole diameters by one fourth inch (1/4") height.
Body Mounting Pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable.
Body Mounting Pad
p/n: 70-0265-48
This Body to Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs in metal bucket cups. Fully molded high quality EPDM rubber.
Body Mounting Pad
p/n: 60-0119-48
This Body Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with metal core and metal bolt liner.
Body Mounting Pad
p/n: 40-0232-48
Pad, body mounting, upper. Fully molded rubber with locating collar. As many as twelve (12) used per car. One and fifteen sixteenths inch (1 15/16") outside width by two inch (2") outside width. See drawing for more dimensions.
Body Mounting Pad
p/n: 40-0453-48
Insulator, body mounting. Fully molded rubber with locating collar. Use as required. Up to eight (8) are used per car.
Body Mounting Pad
p/n: 70-0634-48
Pad, body mounting to frame bracket. Fully molded rubber, rectangular.
Body Mounting Pad
p/n: 70-0635-48
Cushion, body mounting pad. For underside of body bracket. Fully molded rubber with locating collar.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Body Mounting Pad
p/n: 50-0478-48
Pad, body mounting. Fully molded rubber with locating collar. Two (2) are needed per car.
Body Mounting Pad
p/n: 50-0231-48
Shim, body sill. Fully molded rectangular rubber. A total of six (6) are needed per car.
Body Mounting Pad
p/n: 50-0130-48
Pad, body mounting. Fully molded rectangular rubber with locating collar.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.
Body Mounting Pad
p/n: 20-0553-48
Pad, front of cab to frame. Lower. Fully molded rubber with locating collar.
Body Mounting Pad
p/n: 50-0329-48
Pad, body mounting. Under frame bracket for hold-down nut. Fully molded rubber. Check number needed for your particular body.
Body Mounting Pad
p/n: 60-0027-48
Pad, side body mounting. Fully molded rubber, rectangular. Two and seven-sixteenths inch (2-7/16") outside length by one and five-eights inch (1-5/8") outside width by one-fourth inch (1/4") height.
Body Mounting Pad
p/n: 50-0232-48
Shim, body sill, for #3, #5, and #7 body bolts. Six (6) per car. Width: 2.0 inches. Height: 2.0 inches.
Body Mounting Pad
p/n: 40-0231-48
Pad, body mounting, upper. Fully molded rubber with locating collar. One and fifteen sixteenths inch (1 15/16") outside diameter by three fourths inch (3/4") locating collar outside diameter by one half inch (1/2") inside locating hole diameter.
Body Mount Isolator Pad
p/n: 40-0234-48
This Body Mount Isolator Pad functions as a body to frame isolator mounting pad. Made of high quality EPDM rubber with a high level of fit and finish.
Body Mounting Pad
p/n: 40-0230-48
Pad, body mounting, lower. Fully molded rubber. One and eleven sixteenths inch (1 11/16") outside diameter by nine sixteenths inch (9/16") inside hole diameter by one half inch (1/2") height.
Body Mounting Pad
p/n: 70-2603-48
Cushion, body mounting pad. Fully molded rubber with locating collar.
Body Mounting Pad
p/n: 70-2604-48
Cushion, body mounting pad. Fully molded rubber. One and nine sixteenths inch (1 9/16") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by three fourths inch (3/4") height.
Body Mount Isolator Pad
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
Body Mounting Pad
p/n: 40-0229-48
Pad, body mounting, upper. Fully molded rubber. One and three fourths inch (1-3/4") outside diameter by one half inch (1/2") inside hole diameter by one fourth inch (1/4") height.
Body Mounting Pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Bumper Support Bar Pad
p/n: 60-0544-30
A fully molded rubber Bumper Support Bar Pad. Thes part installs between the bumper support bar and bumper face bar at the mounting bolts. Use as required, eight (8) are needed for most cars.
Body Mounting Pad
p/n: 50-0328-48
Pad, body mounting to frame. Fully molded rubber. Up to twenty (20) required per car. Check number needed for your particular body. Two inch (2") square by five eights inch (5/8") inside hole diameter by seven sixteenths inch (7/16") height.
Body Mounting Pad
p/n: 50-0133-48
Pad, body mounting. Fully molded rubber. Two inches (2") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Body Mounting Pad
p/n: 50-0132-48
Pad, body mounting. Fully molded rubber. One and three fourths inch (1 3/4") outside diameter by three eighths inch (3/8") inside hole diameter by five sixteenths inch (5/16") height.
Body Mounting Pad
p/n: 40-0324-48
Cushion, used as either a body mounting pad or for all body bolt nuts, below brackets. Fully molded rubber. Two inch (2") outside diameter by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Body Mounting Pad
p/n: 70-1430-48
Pad, body mounting. Fully molded rubber. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car.
Body Mounting Pad
p/n: 70-2605-48
Cushion, body mounting pad. Fully molded rubber with locating collar.