Door Bumper
p/n: 60-0603-71
Pad, door jamb edge. With metal insert as original.Length: 1.1875 inches. Width: 1.5625 inches.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Door Bumper
p/n: 40-0262-70
Bumper, door.Chrysler 1934 Bumper, door. Chrysler 1932-34 Bumper, decklid. Two (2) required per car. Length: 2.50 inches. Width: 1.8125 inches.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Door Bumper
p/n: 34-0469-71
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Door Hinge Bumper Set
p/n: 70-4871-71
This Door Hinge Bumper Set is a quality reproduction of the original factory part. These sixteen (16) rubber bumpers attach four (4) per door to cushion the door closure action.
Door Bumper
p/n: 10-0011-70
Cushion, door wedge plate, right and left, for door aligning lug receiver.Width: 1.1875 inches. Height: .625 inches.
Rear Door Bumpers
p/n: 60-0334-71
A Rear Door Bumper pair for the door check link above door. Dovetail base fits check arm.
Door Lock Bumper
p/n: 70-0538-71
Bumper, door lock striker plate. Rubber with steel core, seven sixteenths (7/16) inch thick, one (1) per door. Installed in rotary latch receiver.
Door Bumper
p/n: 17-0041-70
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
Door Bumper
p/n: 17-0038-70
Wedge cushion, door dovetail. This is the rubber block which goes behind the dovetail receiving bumper or shoe.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Door Bumper
p/n: 30-0152-71
Bumper, door, rubber, round style, screw retained. One and five sixteenths (1-5/16) inch diameter.
Door Bumper
p/n: 40-0131-70
Bumper, door side. Approximate size one half (1/2) inch by three fourth (3/4) inch by two (2) inch. Length: 2.0 inches. Width: .50 inches.
Door Bumper
p/n: 33-0449-71
Bumper, door, lower, held by one (1) screw and one (1) carrot retainer. Length: 1-1/8 inches. Width: 5/8 inches.
Door Bumper
p/n: 30-0128-71
Pad, door jamb (Atwood type), one and five eighths (1-5/8) inch long.Width: 1.5625 inches. Height: 1.375 inches.
Door Bumper
p/n: 17-0039-71
Bumper, round door side. An auxiliary door side bumper on door jamb pad.
Door Bumper
p/n: 30-0052-71
Bumper, door side, upper. Oblong type, perfect copy of original.Length: 2.4375 inches.
Door Bumper
p/n: 17-0040-71
Bumper, oblong, door side. An auxiliary door jamb or side bumper.Width: 1.75 inches. Height: .75 inches.
Door Bumper Set
p/n: 20-2365-71
Set, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Door Bumper
p/n: 40-0316-70
Bumper, door side, lower, on lock post. Retained by dovetail tapping plate.Length: 1.5625 inches. Width: 1.5625 inches.
Door Bumper
p/n: 34-0342-71
Door bumper, round, rubber with steel insert, (called door anti-rattle). Two (2) per door on all closed body styles, one (1) per door on convertible Sedan.
Rear Door Bumpers
p/n: 70-2365-71
This Rear Door Bumper pair is made from high-quality EPDM dense rubber to provide excellent durability. Fits at the rear door opening. Proper configuration with slots for retaining screws as original.
Bumper - LH Back Door
p/n: 60-0333-71
A molded rubber Left-Hand Back Door Bumper. Dovetail to be used with old castings.
Door Bumper
p/n: 30-0429-71
Bumper, rear door. Two (2) used per car. Correct design with proper clearance for screw hole.Width: 1.0 inches. Height: 1.0 inches.
Door Bumper
p/n: 60-0581-71
Pad, door jamb. (Door side bumper). Two screw type with metal reinforcing inserts.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Bumper
p/n: 10-0126-71
Pad, door jamb. One (1) required per door. Made to fit old door pad core.
Rear Hatch Door Bumpers
p/n: 70-4731-87
This Rear Hatch Door Bumper pair is a quality reproduction of the original factory part. These adjustable rubber bumpers attach to the rear hatch door to prevent the hatch lid from vibrating.
Door Bumper Pad
p/n: 30-0032-71
This circular shaped Door Bumper Pad is designed from the original part for an authentic fit, finish, and appearance.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Door Bumper
p/n: 70-2292-70
Steele Rubber Products has the best quality door bumpers for your Street Rod or Custom Build project. Excellent for use in many applications.
Door Bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Door Bumper
p/n: 30-0350-71
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Rear Hatch Door Bumpers
p/n: 70-4730-87
This Rear Hatch Door Bumper pair is a quality reproduction of the original factory part. These adjustable rubber bumpers attach to the rear hatch door to prevent the hatch lid from vibrating.
Bumpers - Filler Door/Lower Door/Rear License Plate Support
p/n: 20-1302-41
A rubber Bumper pair designed from the original part for superior fitment, finish and function. Fits to the lower door and / or the fuel filler cover and / or the license plate support. Type with threaded end.
Door Bumper
p/n: 20-0003-71
Bumpers, door. Seven sixteenths (7/16) inch high. Fits on door jamb where rear of door closes against body and on rear lower part of door.
Door Jamb Bumper Pad
p/n: 40-0042-70
This Door Jamb Bumper Pad is designed from the original part for superior fitment and seal. A reproduction of earlier type, screw retained and a perfect copy.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Door Bumper
p/n: 60-0048-71
Bumper, door side. Five eighths (5/8) inch by seven eighths (7/8) inch by one and seven sixteenths (1-7/16) inch. Two (2) door.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 30-0064-71
This fully molded slotted type Door Bumper is quality reproduction of the original factory part. Used two (2) per golf door and four (4) to eight (8) per car on open model doors.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
Door Alignment Pad
p/n: 60-0060-71
Wedge pad, door aligning dovetail. Goes under bumper retainer.Length: .9375 inches. Width: .9375 inches. Height: .4375 inches.
Door Bumper
p/n: 60-0032-71
Pad, door jamb. One (1) per door.Length: 1.25 inches. Width: .75 inches. Height: .875 inches.
Lower Door and Fuel Tank Door Bumpers
p/n: 20-0004-71
Manufactured to OEM specifications this Lower Door and Fuel Tank Door Bumper pair installs for an authentic fit, finish and function. Five eighths (5/8") inches high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Bumper
p/n: 30-0312-71
Pad, door jamb. Usually requires two (2) per door.Length: 1.0 inches. Width: 1.0 inches. Height: .50 inches.
Door Bumper
p/n: 33-0503-71
This fully molded 3/4” Door Bumper is quality reproduction of the original factory part. Not a generic substitute but manufactured just like the factory original.
