Fuel Tank To Filler Pipe Seal
p/n: 70-5004-41
This Fuel Tank To Filler Pipe Seal is designed from the original part for superior fitment and seal. This part fits around the vehicle fuel filler pipe where the filler pipe enters the fuel tank.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Fuel Filler Cover Bumper
p/n: 33-0557-15
Bumper, taillight body upper half and fuel filler cover to lower half. Four (4) per set. Length: 13/16 inches. Width: 1/2 inches.
Fuel Tank To Filler Pipe Grommet
p/n: 70-5005-39
This Fuel Tank To Filler Pipe Grommet is designed from the original part for superior fitment and seal. This fuel resistant rubber grommet fits to seal the filler pipe into the fuel tank connection.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Fuel Line Grommet
p/n: 30-0320-41
Grommet, fuel line through engine pan. Two and one fourth (2-1/4) inch diameter.
Fuel Filler Pipe To Trunk Floor Seal
p/n: 20-2739-41
This Fuel Filler Pipe To Trunk Floor Seal is designed from the original part for superior fitment and seal. This part fits around the vehicle fuel filler pipe where the filler pipe goes through the trunk floor.
Fuel Filler Neck Inner Panel Grommet
p/n: 70-1908-41
This Fuel Filler Neck Inner Panel Grommet is designed from the original part for superior fitment and seal. This flat grommet fits around the vehicles fuel filler neck at the inner panel.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Choke Cable Support At Ignition Cable Grommet
p/n: 60-0373-13
This Choke Cable Support At Ignition Cable Grommet is designed from the original part for superior fitment and function.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Fuel Line Grommet
p/n: 70-2239-41
Grommet, fuel lines that run from the fuel tank to the vapor tank mounted on the left front fender well.
Fuel Tank Filler Hose - Rear Tank
p/n: 70-5011-41
This Fuel Tank Filler Neck Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose set connects the rear fuel tank to the filler pipe on Styleside models.
Fuel Tank To Apron Anti-Squeak Channel and Plugs
p/n: 20-2014-41
This Fuel Tank To Apron Anti-Squeak Channel and Plugs set is designed from the original part for an authentic fit, finish, and appearance. Rubber channel fits between the fuel tank and apron. Includes 4 rubber bumper plugs.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Accelerator Lever to Accelerator Shaft Seal
p/n: 70-4098-40
This Accelerator Lever to Accelerator Shaft Seal is designed from the original part for superior fitment and seal. This seal mounts directly to cover and protect the accelerator lever to accelerator shaft rod linkage connection.