1/8" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.
Fuel Door Bumper
p/n: 33-3450-41
Bumper, fuel door. Pushes into body inside fuel filler recess. 5/16" head length by 5/32" head height. Two (2) required per car.
1/8" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.
1/4" Standard Bumper
p/n: 33-0496-71
This Standard Bumper is fully molded and designed from the original part for correct fitment and seal. Designed for applications such as door opening at upper corner, license plate, and fuel filler door. Self-retaining type bumper.
Standard bumper
p/n: 20-1852-41
Bumper, fuel tank filler lid. Gray rubber.Ford Cars 1960-63 Bumper, license plate rubber. Used on rear bumper. 2 required per car.
Fuel Filler Door Bumper
p/n: 33-0538-41
This Fuel Filler Door Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the Fuel Filler Door to support / cushion the closure and prevent metal to metal contact. Usually requires two (2) bumpers each per vehicle.
Accelerator Pedal Rod Firewall Grommet
p/n: 20-2744-41
This Accelerator Pedal Rod Firewall Grommet is used to run the accelerator pedal rod through the firewall. Designed from original part so it fits correctly.
1/8" Taillight Bumper
p/n: 33-0556-15
Taillight body upper half and fuel filler cover to lower half bumper.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
1" Fuel Line Grommet
p/n: 32-0714-41
This Fuel Line Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed to run the fuel line through the firewall.
Accelerator Pedal Rod Seal
p/n: 20-1448-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from original part so it fits correctly.
Accelerator Pedal Rod Seal
p/n: 20-1449-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Made from top quality rubber to ensure durability and proper fitment.
1/4" Fuel Tank Mounting Isolator Strapping
p/n: 70-3612-99
Universal 1/4" Fuel Tank Mounting Isolator Strapping. Made of high quality 60 durometer EPDM dense rubber for a variety of uses. Available by the foot.
Fuel filler cover bumper
p/n: 20-0006-41
Bumpers, fuel tank door. Single stem and double retainer bumper set.
Accelerator Pedal Rod Seal
p/n: 20-0128-41
This Accelerator Pedal Rod Seal is used to wrap around the accelerator rod linkage at the firewall. Designed from original part so it fits correctly.
Accelerator Pedal Rod Seal
p/n: 20-1450-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from the original part for superior fit and seal.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Fuel Tank To Filler Pipe Hose
p/n: 70-5001-41
This Fuel Tank To Filler Pipe Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose connects the fuel tank to the filler pipe.
Fuel Tank Vapor Valve Grommet
p/n: 70-5008-41
Made from fuel resistant rubber this Fuel Tank Vapor Valve Grommet seals the Fuel Vapor Valve to the fuel tank.
Fuel Tank To Filler Neck Hose
p/n: 20-2740-41
This Fuel Tank To Filler Neck Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose connects the fuel tank to the filler pipe.
Fuel Tank To Filler Pipe Hose
p/n: 70-5000-41
This Fuel Tank To Filler Pipe Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose connects the fuel tank to the filler pipe.
Fuel Tank Support Pad
p/n: 20-0425-41
This Fuel Tank Support Pad pair installs between the fuel tank and floor to reduce noise. Designed from original specifications so it fits correctly.
Bumpers - Filler Door/Lower Door/Rear License Plate Support
p/n: 20-1302-41
A rubber Bumper pair designed from the original part for superior fitment, finish and function. Fits to the lower door and / or the fuel filler cover and / or the license plate support. Type with threaded end.
Accelerator Pedal Rod Grommet
p/n: 20-0044-41
This Accelerator Pedal Rod Grommet is used to wrap around the accelerator rod at the firewall. Designed from the original part for superior fit and seal.
Fuel Tank To Filler Pipe Hose
p/n: 70-5003-41
This Fuel Tank To Filler Pipe Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose connects the fuel tank to the filler pipe.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Fuel Tank Filler Neck Connection Hose
p/n: 20-1584-39
This Fuel Tank Filler Neck Connection Hose is designed from the original part for superior fitment and function. Connects the fuel tank to the fuel filler pipe.
Accelerator Hinge Grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard. Length: 3.50 inches. Width: 2.50 inches.
Fuel Tank To Filler Pipe Seal
p/n: 70-5004-41
This Fuel Tank To Filler Pipe Seal is designed from the original part for superior fitment and seal. This part fits around the vehicle fuel filler pipe where the filler pipe enters the fuel tank.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Fuel Filler Cover Bumper
p/n: 33-0557-15
Bumper, taillight body upper half and fuel filler cover to lower half. Four (4) per set. Length: 13/16 inches. Width: 1/2 inches.
Fuel Tank To Filler Pipe Grommet
p/n: 70-5005-39
This Fuel Tank To Filler Pipe Grommet is designed from the original part for superior fitment and seal. This fuel resistant rubber grommet fits to seal the filler pipe into the fuel tank connection.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Fuel Line Grommet
p/n: 30-0320-41
Grommet, fuel line through engine pan. Two and one fourth (2-1/4) inch diameter.
Fuel Filler Pipe To Trunk Floor Seal
p/n: 20-2739-41
This Fuel Filler Pipe To Trunk Floor Seal is designed from the original part for superior fitment and seal. This part fits around the vehicle fuel filler pipe where the filler pipe goes through the trunk floor.
Fuel Filler Neck Inner Panel Grommet
p/n: 70-1908-41
This Fuel Filler Neck Inner Panel Grommet is designed from the original part for superior fitment and seal. This flat grommet fits around the vehicles fuel filler neck at the inner panel.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Choke Cable Support At Ignition Cable Grommet
p/n: 60-0373-13
This Choke Cable Support At Ignition Cable Grommet is designed from the original part for superior fitment and function.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Fuel Line Grommet
p/n: 70-2239-41
Grommet, fuel lines that run from the fuel tank to the vapor tank mounted on the left front fender well.
Fuel Tank Filler Hose - Rear Tank
p/n: 70-5011-41
This Fuel Tank Filler Neck Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose set connects the rear fuel tank to the filler pipe on Styleside models.
Fuel Tank To Apron Anti-Squeak Channel and Plugs
p/n: 20-2014-41
This Fuel Tank To Apron Anti-Squeak Channel and Plugs set is designed from the original part for an authentic fit, finish, and appearance. Rubber channel fits between the fuel tank and apron. Includes 4 rubber bumper plugs.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Accelerator Lever to Accelerator Shaft Seal
p/n: 70-4098-40
This Accelerator Lever to Accelerator Shaft Seal is designed from the original part for superior fitment and seal. This seal mounts directly to cover and protect the accelerator lever to accelerator shaft rod linkage connection.
Fuel Tank Filler Hose
p/n: 70-5009-41
This Fuel Tank Filler Hose is designed from the original part for superior fitment and function. This molded fuel resistant rubber hose connects the fuel tank to the filler pipe.
Fuel tank support pad
p/n: 60-0026-41
Pad, fuel tank support and floorboard seal. Sponge rubber ring. Two (2) per car.
Fuel Neck Grommet
p/n: 16-0001-41
Mounting pad, fuel filler neck bezel, good copy of original. Length: 5.75 inches.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Fuel Neck Grommet
p/n: 30-0101-41
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Fuel Filler Neck Grommet
p/n: 30-0158-41
This Fuel Filler Neck To Body Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Fuel Neck Grommet
p/n: 25-0013-41
Grommet, fuel filler neck. Virtually exact copy for two and one fourth (2-1/4) inch diameter filler neck through body or fender.
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
Filler Neck Extension Pad
p/n: 70-0123-41
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
Fuel Tank Filler Hose Set - Midship Tank
p/n: 70-5006-41
This Fuel Tank Filler Neck Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose set connects the midship fuel tank to the filler pipe on Styleside models.
Air Inlet Hose
p/n: 70-0405-41
Hose, air inlet, radiator shroud to air silencer. Two and one eighths (2-1/8) inch outside diameter by nine and three eighths (9-3/8) inch long. Beautiful copy of rare original part.
Fuel Neck Grommet
p/n: 30-0157-41
Seal, fuel filler neck through rumble seat floor pan. Highest quality workmanship, rubber with brass core as original.
Shaker Hood Air Cleaner Seal
p/n: 20-2766-45
This Shaker Hood Air Cleaner Seal includes drain hose and correct FoMoCo script. Made from Original Ford Tooling.
Carburetor Air Intake Hose
p/n: 70-0290-41
Hoses, carburetor air intake. Two (2) per car. Sixteen and three fourths (16-3/4) inches long, two (2) inches inside diameter one end, two and one fourth (2-1/4) inches inside diameter other end. Trim to proper length when installing.