Carburetor Air Intake Hose
p/n: 70-0290-41
Hoses, carburetor air intake. Two (2) per car. Sixteen and three fourths (16-3/4) inches long, two (2) inches inside diameter one end, two and one fourth (2-1/4) inches inside diameter other end. Trim to proper length when installing.
Shaker Hood Air Cleaner Seal
p/n: 20-2766-45
This Shaker Hood Air Cleaner Seal includes drain hose and correct FoMoCo script. Made from Original Ford Tooling.
Fuel Neck Grommet
p/n: 30-0157-41
Seal, fuel filler neck through rumble seat floor pan. Highest quality workmanship, rubber with brass core as original.
Air Inlet Hose
p/n: 70-0405-41
Hose, air inlet, radiator shroud to air silencer. Two and one eighths (2-1/8) inch outside diameter by nine and three eighths (9-3/8) inch long. Beautiful copy of rare original part.
Fuel Tank Filler Hose Set - Midship Tank
p/n: 70-5006-41
This Fuel Tank Filler Neck Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose set connects the midship fuel tank to the filler pipe on Styleside models.
Filler Neck Extension Pad
p/n: 70-0123-41
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
Fuel Neck Grommet
p/n: 25-0013-41
Grommet, fuel filler neck. Virtually exact copy for two and one fourth (2-1/4) inch diameter filler neck through body or fender.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Fuel Filler Neck Grommet
p/n: 30-0158-41
This Fuel Filler Neck To Body Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Neck Grommet
p/n: 30-0101-41
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Fuel Neck Grommet
p/n: 16-0001-41
Mounting pad, fuel filler neck bezel, good copy of original. Length: 5.75 inches.
Fuel tank support pad
p/n: 60-0026-41
Pad, fuel tank support and floorboard seal. Sponge rubber ring. Two (2) per car.
Fuel Tank Filler Hose
p/n: 70-5009-41
This Fuel Tank Filler Hose is designed from the original part for superior fitment and function. This molded fuel resistant rubber hose connects the fuel tank to the filler pipe.
Accelerator Lever to Accelerator Shaft Seal
p/n: 70-4098-40
This Accelerator Lever to Accelerator Shaft Seal is designed from the original part for superior fitment and seal. This seal mounts directly to cover and protect the accelerator lever to accelerator shaft rod linkage connection.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Fuel Tank To Apron Anti-Squeak Channel and Plugs
p/n: 20-2014-41
This Fuel Tank To Apron Anti-Squeak Channel and Plugs set is designed from the original part for an authentic fit, finish, and appearance. Rubber channel fits between the fuel tank and apron. Includes 4 rubber bumper plugs.
Fuel Tank Filler Hose - Rear Tank
p/n: 70-5011-41
This Fuel Tank Filler Neck Hose is designed from the original part for superior fitment and function. This fuel resistant rubber hose set connects the rear fuel tank to the filler pipe on Styleside models.
Fuel Line Grommet
p/n: 70-2239-41
Grommet, fuel lines that run from the fuel tank to the vapor tank mounted on the left front fender well.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Choke Cable Support At Ignition Cable Grommet
p/n: 60-0373-13
This Choke Cable Support At Ignition Cable Grommet is designed from the original part for superior fitment and function.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Fuel Filler Neck Inner Panel Grommet
p/n: 70-1908-41
This Fuel Filler Neck Inner Panel Grommet is designed from the original part for superior fitment and seal. This flat grommet fits around the vehicles fuel filler neck at the inner panel.
Fuel Filler Pipe To Trunk Floor Seal
p/n: 20-2739-41
This Fuel Filler Pipe To Trunk Floor Seal is designed from the original part for superior fitment and seal. This part fits around the vehicle fuel filler pipe where the filler pipe goes through the trunk floor.
Fuel Line Grommet
p/n: 30-0320-41
Grommet, fuel line through engine pan. Two and one fourth (2-1/4) inch diameter.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Fuel Tank To Filler Pipe Grommet
p/n: 70-5005-39
This Fuel Tank To Filler Pipe Grommet is designed from the original part for superior fitment and seal. This fuel resistant rubber grommet fits to seal the filler pipe into the fuel tank connection.
Fuel Filler Cover Bumper
p/n: 33-0557-15
Bumper, taillight body upper half and fuel filler cover to lower half. Four (4) per set. Length: 13/16 inches. Width: 1/2 inches.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Fuel Tank To Filler Pipe Seal
p/n: 70-5004-41
This Fuel Tank To Filler Pipe Seal is designed from the original part for superior fitment and seal. This part fits around the vehicle fuel filler pipe where the filler pipe enters the fuel tank.
Accelerator Hinge Grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard. Length: 3.50 inches. Width: 2.50 inches.