Hood Vent Bumper
p/n: 33-0053-42
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Hood Louver Corner Stop
p/n: 33-0129-42
Corner stop, hood louver, self-holding, original size and profile, fits one fourth (1/4) inch hole in sheet metal.
Hood Bumper Set
p/n: 33-0680-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Bumper Set
p/n: 33-0681-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Fuel Filler Cover Bumper
p/n: 33-0557-15
Bumper, taillight body upper half and fuel filler cover to lower half. Four (4) per set. Length: 13/16 inches. Width: 1/2 inches.
Door Bumper
p/n: 33-0449-71
Bumper, door, lower, held by one (1) screw and one (1) carrot retainer. Length: 1-1/8 inches. Width: 5/8 inches.
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
This Cowl Drain Gutter Hose Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Windshield Post Bumper
p/n: 33-0037-52
Bumper, windshield post (side arm). Replaces #366138. Two (2) per car.
Fender Bumper
p/n: 33-0441-44
Bumper, between grill and fender. One fourth (1/4) inch thickness, five sixteenths (5/16) inch sheet metal holes.
Door Bumper
p/n: 33-0503-71
This fully molded 3/4” Door Bumper is quality reproduction of the original factory part. Not a generic substitute but manufactured just like the factory original.
Fender Bumper
p/n: 33-0545-30
Bumper, fender extension to quarter panel. Fully molded rubber. One and one fourths inch (1-1/4") length by eleven sixteenths inch (11/16") base diameter.
5/16" Door Bumper
p/n: 33-0293-71
Bumper, front door pillar, upper and lower. Replaces factory #3720168.
1/4" Radiator Panel Bumper
p/n: 33-0211-31
Lower radiator panel to grille bumper. Also used on radiator valance.
5/16" Hood Side to Fender Bumper
p/n: 33-0542-42
A quality Hood Side To Fender Bumper. Button type and self-retaining. Replaces factory #391463.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
1/8" Taillight Bumper
p/n: 33-0556-15
Taillight body upper half and fuel filler cover to lower half bumper.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
3/16" Hood Vent Bumper
p/n: 33-0042-42
Hood ventilator door bumper, stem retainer. Twelve (12) required per car.
3/8" Gravel Shield Bumper
p/n: 33-0016-45
Bumper, gravel deflector. Self retaining, round button style, used as anti-rattle to front bumper support bar.
1/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
Fuel Filler Door Bumper
p/n: 33-0538-41
This Fuel Filler Door Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the Fuel Filler Door to support / cushion the closure and prevent metal to metal contact. Usually requires two (2) bumpers each per vehicle.
1/4" Inner Fender Bumper
p/n: 33-0512-44
Inner fender to inner splash pan bumper. This bumper is not a generic replacement, and will only be seen when inner fender is removed.
1/4" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
5/16" Hood Bumper
p/n: 33-0031-42
Self-retaining hood bumper, along edge of hood against fender. Up to twenty (20) per car.
1/4" Standard Bumper
p/n: 33-0496-71
This Standard Bumper is fully molded and designed from the original part for correct fitment and seal. Designed for applications such as door opening at upper corner, license plate, and fuel filler door. Self-retaining type bumper.
3/16" Trunk Bumper
p/n: 33-0990-87
This Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
1/4" Hood Bumper
p/n: 33-0003-42
Bumper, hood, 2 uses. Hood to radiator shell at side panel, hood to fender, as required.
1/4" Standard Bumper
p/n: 33-0136-42
This Standard Bumper is fully molded from quality dense rubber to provide excellent durability. Commonly used as a door bumper on the center upper post on post model vehicles.
3/16" Cowl Vent Louver Bumper
p/n: 33-0348-54
This Cowl Vent Louver Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Door Bumper
p/n: 33-1234-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1235-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1233-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1232-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Hood Bumper
p/n: 33-0861-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Rear License Plate Bracket Bumper
p/n: 70-4478-45
This Rear License Plate Bracket Bumper is designed from the original part for superior fitment and function. This OEM exact copy reproduction bumper mounts in the spring retainer on the license plate bracket.
1/4" Trunk Bumper
p/n: 33-0350-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Bumper fits to the rear compartment lid, lower corners on lid. Two (2) per car. Manufactured to OEM specifications to install for an authentic fit, finish, and function.
5/16" Side Window Bumper
p/n: 33-0516-71
This Side Window Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as an anti-rattle door window garnish molding. Two (2) required per door.
1/8" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.
1/8" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.
3/16" License Plate Bumper
p/n: 33-0349-87
This License Plate Bumper is fully molded and designed from the original part for correct fitment and seal. This bumper is made from quality dense rubber to provide excellent durability.